Bassey et al. (2020). Cardiovascular disease risk factors and markers of oxidative stress and DNA damage in leprosy patients in Southern Nigeria. PLoS Negl Trop Dis. 2020 Oct 12;14(10):e0008749. doi: 10.1371/journal.pntd.0008749. PMID: 33044965; PMCID: PMC7580906.
Rubisco (Ribulose-1,5-bisphosphate carboxylase/oxygenase) catalyzes the rate-limiting step of CO2 fixation in photosynthetic organisms. Form II Rubisco is present in many photosynthetic bacteria and archaea and in some photosynthetic dinoflagellates.Source of Rubisco standard: Overexpressed RbcL form II protein
Product Type:
Antibody
Format:
Lyophilized in glycerol.
Storage Temp:
Store lyophilized/reconstituted at -20 °C; once reconstituted make aliquots to avoid repeated freeze-thaw cycles. Please remember to spin the tubes briefly prior to opening them to avoid any losses that might occur from material adhering to the cap or sides of the tube.
Concentration: after re-constitution with sterile milliQ water final concentration of the standard is 0.15 pmoles/ lProtein standard buffer composition: Glycerol 10%, Tris Base 141 mM, Tris HCl 106 mM, LDS 2%, EDTA 0.51 mM, SERVA Blue G250 0.22 mM, Phenol Red 0.175 mM, pH 8.5, 0.1mg/ml PefaBloc protease inhibitor (Roche), 50 mM DTT.This standard is ready-to-load and does not require any additions or heating. It needs to be fully thawed and thoroughly mixed prior to using. Avoid vigorous vortexing, as buffers contain detergent. Following mixing, briefly pulse in a microcentrifuge to collect material from cap.This standard is stabilized and ready and does not require heating before loading on the gel. Please note that this product contains 10% glycerol and might appear as liquid but is provided lyophilized. Allow the product several minutes to solubilize after adding water. Mix thoroughly but gently Take extra care to mix thoroughly before each use, as the proteins tend to settle with the more dense layer after freezing.Please, use the 55 kDa size of RbcL for calculations. The pmoles in the standard refer to pmoles of rbcL monomers.
Application Details:
Standard curve: 3 loads are recommended (0.5, 2 and 4μl).For most applications a sample load of 0.2 μg of chlorophyll/well will give a RbcL signal in this range.Positive control: a 2 μl load per well is optimal for most chemiluminescent detection systems. Higher standard concentration needs to be used to allow detection by Coomasie stains. Such gels with higher standard concentration can not be used for quantitation using chemiluminescence.This standard is stabilized and ready and does not require heating before loading on the gel.Please note that this product contains 10% glycerol and might appear as liquid but is provided lyophilized. Allow the product several minutes to solubilize after adding water. Mix thoroughly but gently Take extra care to mix thoroughly before each use, as the proteins tend to settle with the more dense layer after freezing.
Reconstitution:
For reconstitution add 90 μl of sterile water, Please notice that this product contains 10% glycerol and might appear as liquid but is provided lyophilized
Molecular Weight:
52,7 kDa
Selected references:
Bausch et al. (2019). Combined effects of simulated acidification and hypoxia on the harmful dinoflagellate Amphidinium carterae. Mar Biol 166: 80. https://doi.org/10.1007/s00227-019-3528-y.
Special application note:
The RbcL protein standard can be used in a combination with Agrisera global antibiodies (AS15 2955 from rabbit) to quantitate RbcL from a wide range of species. Global antibodies are raised against highly conserved amino acid sequence. This standard is also included in following kits: Educational antibody kit - photosynthesis, Photosynthesis Tool Kit - quantitation, Rubico quantitation kit,Quantitative western blot: detailed method description, video tutorial
SBPase (Sedoheptulose-1,7-bis phosphatase) is a chloroplast enzyme involved in the carbon reduction of the Calvin cycle, part of carbohydrate metabolism.Source of SBPase standard: SBPase standard source is Sphingomonas wittichii strain RW1, overexpressed in E.coli bearing an N-terminal his6 tag.
Product Type:
Antibody
Format:
Lyophilized
Storage Temp:
Store lyophilized/reconstituted at -20 °C; once reconstituted make aliquots to avoid repeated freeze-thaw cycles. Please remember to spin the tubes briefly prior to opening them to avoid any losses that might occur from material adhering to the cap or sides of the tube.
Concentration: after re-constitution with sterile milliQ water final concentration of the standard is 0.15 pmoles/ lProtein standard buffer composition: Glycerol 10%, Tris Base 141 mM, Tris HCl 106 mM, LDS 2%, EDTA 0.51 mM, SERVA Blue G250 0.22 mM, Phenol Red 0.175 mM, pH 8.5, 0.1mg/ml PefaBloc protease inhibitor (Roche), 50 mM DTT.This standard is ready-to-load and does not require any additions or heating. It needs to be fully thawed and thoroughly mixed prior to using. Avoid vigorous vortexing, as buffers contain detergent. Following mixing, briefly pulse in a microcentrifuge to collect material from cap.This standard is stabilized and ready and does not require heating before loading on the gel. Please note that this product contains 10% glycerol and might appear as liquid but is provided lyophilized. Allow the product several minutes to solubilize after adding water. Mix thoroughly but gently Take extra care to mix thoroughly before each use, as the proteins tend to settle with the more dense layer after freezing.
Application Details:
Standard curve: 3 loads are recommended (0.5, 2 and 4μl).For most applications a sample load of 0.2 μg of chlorophyll/well will give a RbcL signal in this range.Positive control: a 2 μl load per well is optimal for most chemiluminescent detection systems. Higher standard concentration needs to be used to allow detection by Coomasie stains. Such gels with higher standard concentration can not be used for quantitation using chemiluminescence.This standard is stabilized and ready and does not require heating before loading on the gel.Please note that this product contains 10% glycerol and might appear as liquid but is provided lyophilized. Allow the product several minutes to solubilize after adding water. Mix thoroughly but gently Take extra care to mix thoroughly before each use, as the proteins tend to settle with the more dense layer after freezing.
Reconstitution:
For reconstitution add 85 l of sterile water, Please note that this product contains glycerol and might appear as liquid but is provided lyophilized
Molecular Weight:
27 kDa
Special application note:
The SBPase calibrated protein standard can be used in combination with Agrisera global anti-SBPase antibiodies (AS15 2873) to quantitate SBPase from a wide range of species. Global antibodies are raised against highly conserved amino acid sequence. Quantitative western blot: detailed method description and video tutorial.
Heat-shock protein 70 (Hsp70) is the major stress-inducible protein in vertebrates and is highly conserved throughout evolution. It plays a role as a molecular chaperone and is important for allowing cells to cope with acute stressor insult, especially those affecting the protein machinery. Heat shock cognate protein 70 (HSC70), is a highly conserved protein and a member of the family of molecular chaperones.Source of HSP70 standard: recombinant Hsp70 of Arabidopsis thaliana UniProt: Q9LHA8, TAIR: AT3G12580
Product Type:
Antibody
Format:
Lyophilized in glycerol
Storage Temp:
Store lyophilized/reconstituted at -20 °C; once reconstituted make aliquots to avoid repeated freeze-thaw cycles. Please remember to spin the tubes briefly prior to opening them to avoid any losses that might occur from material adhering to the cap or sides of the tube.
Concentration: after re-constitution with sterile milliQ water final concentration of the standard is 0.15 pmoles/ lProtein standard buffer composition: Glycerol 10%, Tris Base 141 mM, Tris HCl 106 mM, LDS 2%, EDTA 0.51 mM, SERVA Blue G250 0.22 mM, Phenol Red 0.175 mM, pH 8.5, 0.1mg/ml PefaBloc protease inhibitor (Roche), 50 mM DTT.This standard is ready-to-load and does not require any additions or heating. It needs to be fully thawed and thoroughly mixed prior to using. Avoid vigorous vortexing, as buffers contain detergent. Following mixing, briefly pulse in a microcentrifuge to collect material from cap.This standard is stabilized and ready and does not require heating before loading on the gel. Please note that this product contains 10% glycerol and might appear as liquid but is provided lyophilized. Allow the product several minutes to solubilize after adding water. Mix thoroughly but gently Take extra care to mix thoroughly before each use, as the proteins tend to settle with the more dense layer after freezing.
Application Details:
Standard curve: 3 loads are recommended (eg 0.1, 0.2, 0.3 pmol). Adjust range to fit your samples and your experiment. For most applications a sample load of 0.2 μg of chlorophyll/well will give a HSP70 signal in this range.Positive control: a 2 μl load per well is optimal for most chemiluminescent detection systems. Higher standard concentration needs to be used to allow detection by Coomasie stains. Such gels with higher standard concentration can not be used for quantitation using chemiluminescence.This standard is stabilized and ready and does not require heating before loading on the gel.Please note that this product contains 10% glycerol and might appear as liquid but is provided lyophilized. Allow the product several minutes to solubilize after adding water. Mix thoroughly but gently. Take extra care to mix thoroughly before each use, as the proteins tend to settle with the more dense layer after freezing.
Reconstitution:
For reconstitution add 82 l of steril water. Please notice that this product contains glycerol and might appear as liquid but is provided lyophilized. Final standard concentration is going to be 0.15 pmol/ l
Molecular Weight:
70 kDa
Special application note:
The HSP70 protein standard can be used in a combination with Agrisera global antibiodies (AS08 371) to quantitate HSP70 from a wide range of species. Global antibodies are raised against highly conserved amino acid sequence. Quantitative western blot: detailed method description, video tutorial
Storage of tissue samples. The aluminium cryo vials with screw caps can be used for storage of tissue samples. The cryo tubes are suitable for storage of tissue samples in liquid nitrogen. Suitable for deepfreezing till -196°C. Autoclavable at 121°C . Available in 3ml (PA6003) and 15ml (PA6015) (sets of 100 pieces).
Storage of cryo tubes in liquid nitrogen: 1) Place the tissue in the cryo tube, 2) Close the cryotube tighly and place the cryotube in the liquid nitrogen for 1 minute, 3) The cryo vials can be stored at -80°C. Use of cryo tube in combination with isopentane: 1)Place a cup with isopentane in the liquid nitrogen; after approximately 2 minutes the isopentane clot and have a temperature of -160°C. 2)Place the tissue sample or biopsy in the isopentane for 30 seconds, 3) Place the tissue in the cryo vials and store at -80°C.
Reagent preparation:
Make sure that the cap and the vial have the same temperature because the material could slightly shrink or expand under influence of excessive temperature differences.
Expected results:
Long term storage of tissue
Precautions:
Wear a face mask at all times, Check if the screw treads and the lid are okay, Screw the lid on tightly. Attention: AVOID EXCESSIVE TEMPERATURE CHANGES, the cap could explode from the cryo tube.
Storage of tissue samples. The aluminium cryo vials with screw caps can be used for storage of tissue samples. The cryo tubes are suitable for storage of tissue samples in liquid nitrogen. Suitable for deepfreezing till -196°C. Autoclavable at 121°C . Available in 3ml (PA6003) and 15ml (PA6015) (sets of 100 pieces).
Storage of cryo tubes in liquid nitrogen: 1) Place the tissue in the cryo tube, 2) Close the cryotube tighly and place the cryotube in the liquid nitrogen for 1 minute, 3) The cryo vials can be stored at -80°C. Use of cryo tube in combination with isopentane: 1)Place a cup with isopentane in the liquid nitrogen; after approximately 2 minutes the isopentane clot and have a temperature of -160°C. 2)Place the tissue sample or biopsy in the isopentane for 30 seconds, 3) Place the tissue in the cryo vials and store at -80°C.
Reagent preparation:
Make sure that the cap and the vial have the same temperature because the material could slightly shrink or expand under influence of excessive temperature differences.
Expected results:
Long term storage of tissue
Precautions:
Wear a face mask at all times, Check if the screw treads and the lid are okay, Screw the lid on tightly. Attention: AVOID EXCESSIVE TEMPERATURE CHANGES, the cap could explode from the cryo tube.
The BrightDAB substrate DAB (3,3Diaminobenzidine) is a widely used chromogen for immunohistochemical staining and immunoblotting. When in the presence of peroxidase enzyme, DAB produces a brown precipitate that is insoluble in alcohol and xylene. This product comes in a two-component system consisting of a liquid stable DAB chromogen and DAB substrate buffer. DAB Solution A: Readyto-Use Buffered H2O2,; DAB Solution B: Concentrated DAB solution. BrightDAB is a very stable and superior formulation of DAB. In some cases, antibodies titers may increase by two-fold. BrightDAB can be used both manually and on automated stainers. The clinical interpretation of any staining or its absence should be determined by a qualified pathologist and complemented by morphologic studies; controls should be evaluated within the context of the patients clinical history and/or other diagnostic tests. Also available in 500 ml and 1000 ml.
Principle of method:
DAB substrate for use with HRP-labeled detection systems
Reagents provided:
DAB Solution A: Buffered H2O2 (Ready-to-Use) 110 ml DAB Solution B: Concentrated DAB solution 5 ml
Storage and handling:
2-8°C and in the dark
Reagent preparation:
1 Working solution: Add 40 ?l DAB Solution B (± one drop) to 1 ml Solution A, mix well. 2 Incubate the DAB solution one time 8 minutes without washing in between.
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary mouse or rabbit antibody (Antibody; 30 min), 8. Wash buffer (PBS or TBS buffer; 2x 5 min), 9. Detection system, polymer HRP, (Labeled polymer; 30 min), 10. Wash buffer (PBS or TBS buffer; 2x 5 min), 11. Substrate (DAB; 8 min), 12. Wash aqua dest (Wash; 2x 2 min), 13. Counterstain, dehydrate and coverslip (Auxiliary)
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
The Plus HRP Kits, Mouse is based on the streptavidin-biotin system. It is designed for qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with monoclonal primary antibodies and sera obtained from mice. The Plus HRP Kit, Mouse can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Kit, Mouse is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and horse radish peroxidase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus HRP Kit, Mouse binds to mouse primary antibodies. Therefore this kit can detect monoclonal primary antibodies and sera obtained from mice.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide Block). Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and the streptavidin-horse radish peroxidase-conjugate (Streptavidin-HRP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-HRP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed via a light microscope. The chromogen used determines the colour. The chromogen AEC (included only in kit MON-APP123) leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB (included only in kit MON-APP124) forms a dark brown precipitate.
Reagents provided:
8 ml Peroxide Block (ready-to-use) 8 ml Blocking Solution Reagent 1 (ready-to-use) 8 ml Biotinylated Secondary Antibody, Mouse Reagent 2 (ready-to-use) 8 ml Streptavidin-HRP-Conjugate Reagent 3 (ready-to-use) 7 x 5 ml DAB Substrate Buffer 3 ml DAB Concentrate (Chromogen) Substrate systems recommended (if not included in the kit): Permanent AEC kit, AEC single solution, AEC substrate kit, DAB substrate kit, DAB high contrast kit. Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. The tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate AEC working solution (with MON-APP123 only): Add 2 drops (100 µl) of AEC Concentrate to one bottle of AEC Substrate Buffer and mix thoroughly. Preparation of the chromogenic substrate DAB working solution (with MON-APP124 only): Add 4 drops (200 µl) of DAB Concentrate to one bottle of DAB Substrate Buffer and mix thoroughly
Procedure:
1. Peroxide Block (3% H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 2 min. 7. Biotinylated Secondary Antibody, Mouse (Reagent 2, yellow) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Streptavidin-HRP-Conjugate (Reagent 3, red) 10-15 min. 10. Washing with wash buffer 3 x 2 min. 11. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 12. Stopping the reaction with distilled H2O when the desired colour intensity is attained 13. Counterstaining and blueing 14. Mounting: aqueous with AEC, permanent with DAB or Permanent AEC
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase. Maybe the hydrogen peroxide solution used for blocking was inactivated. 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with 3% H2O2 solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Background staining due to endogenous biotin can be blocked through an avidinbiotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) are available upon request.
HIER Citrate Buffer pH 6.0 is a solution developed for heat induced epitope retrieval (HIER) in formalin-fixed paraffin-embedded tissue sections on slides. This procedure is primarily used in immunohistochemistry.
Immunohistochemical staining procedures consist of sequential incubation steps with blocking solutions, antibodies and secondary reagents, enzymes and chromogenic substrates carried out on tissue sections. These tissue sections are mostly prepared out of formalin-fixed paraffin-embedded tissue blocks. Cellular structures are very effectively stabilised by formalin fixation which results in optimal morphological preservation of the sample. On the other hand the formalin fixation leads to strong cross-links between proteins. This means that epitopes of antigens are being masked and often are no longer accessible for primary antibodies. In order to enable primary antibodies to bind to the antigens the epitopes have to be recovered. Heat induced epitope retrieval (HIER) in buffer solutions of different compositions and pH-values restore structures of the epitopes making them more accessible to specific antibodies. Enzymatic digestion with proteolytic enzymes is another way of recovering epitopes. The primary antibody used determines the appropriate method.
Principle of method:
HIER Citrate Buffer pH 6.0 is a 10fold concentrated citrate buffer solution with additives of stabilising substances. For preparation of the working strength solution the buffer concentrate is diluted 1:10 with deionised or distilled water. The resulting solution has a pH of 6.0 (5.8 to 6.2). HIER Citrate Buffer pH 6.0 is a very efficient epitope retrieval solution in immunohistochemical staining procedures to be used with primary antibodies of many different specificities.
Reagents provided:
100 ml HIER Citrate Buffer pH 6.0 (10fold concentrated, adequate for 1 litre ready-to-use citrate buffer)
Storage and handling:
The solution should be stored at 2-8°C. Do not free ze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. If stored at room temperature the solution is stable for at least 10 month from the date of delivery. The prepared working strength solution is stable for 1 month, if stored at 2-8°C. A positive and a negat ive control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Reagent preparation:
Preparation of the citrate buffer working strength solution: Dilute HIER Citrate Buffer concentrate 1:10 with deionised or distilled water and mix thoroughly. The pH-value should be at 6.0 (5.8 to 6.2). If necessary adjust pH-value with diluted NaOH or HCl solution.
Procedure:
HIER Citrate Buffer is suitable for various HIER-methods such as steamer, pressure cooker, autoclave, water bath, and microwave oven. Tissue sections used in heat induced epitope retrieval should always be placed on adhesive slides. Epitope retrieval is carried out after dewaxing and rehydration of the sections. Exemplary protocol using steamer: 1. Prepare the working strength solution by diluting the buffer concentrate as described above and transfer to a Coplin jar. Please make sure that there is enough volume to cover the tissue sections on the slides completely. 2. Fill steamer with water according to instruction manual, close lid and start. 3. After 10 minutes place Coplin jar with citrate buffer in the steamer, close the lid and heat the solution for 20 minutes. 4. Place slides with tissue sections into the preheated solution and close the lid. Tissue sections have to be completely covered with citrate buffer solution. 5. Incubate slides 20 40 minutes. The optimal incubation time needs to be elaborated by the operator. 6. After the incubation take the Coplin jar with slides out of steamer and let cool down at room temperature for about 20 minutes. 7. Remove citrate buffer, rinse slides with wash buffer and proceed with immunohistological staining.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific binding. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent or specimen with eye, skin or mucous membrane. In case of the reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. ProClin 300 is used for stabilisation. A material safety data sheet (MSDS) is available upon request.
Blocking Solution is developed to eliminate unspecific binding of primary and secondary antibodies to tissue sections. It is primarily intended to be used in immunohistochemistry on formalin-fixed paraffin-embedded samples.
Unspecific binding of primary and secondary antibodies to tissue sections in immunohistochemical staining procedures can result in background staining. This effect can be eliminated when tissue sections are incubated with Blocking Solution prior to incubation with the primary antibody. The protein in Blocking Solution abolishes unspecific binding. Blocking Solution is a universal blocking reagent. Unlike other frequently used blocking solutions (e. g. serum blocks) the reagent can be used regardless of the origin species of the secondary antibody. Interferences with secondary antibodies or other components of detection systems are not observed. In contrast to other blocking reagents this Blocking Solution should not be incubated longer than 10 minutes and should be rinsed away with wash buffer. Otherwise the signal intensity of the immunohistochemical staining reaction could be decreased.
Principle of method:
Blocking Solution is applied on tissue sections to reduce background staining due to unspecific binding of primary and secondary antibodies in immunohistochemistry. The step is carried out prior to incubation with the primary antibody
Reagents provided:
100 ml Blocking Solution (ready-to-use)
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Procedure:
1. Apply Blocking Solution for 5 minutes at room temperature. The section should be covered completely. 2. Rinse with wash buffer. 3. Proceed with next steps for immunohistochemical staining as usual starting with the primary antibody.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, contact our technical support . Also refer to the instructions of the detection systems containing Blocking Solution for guidance on general troubleshooting
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent or specimen with eye, skin or mucous membrane. In case of the reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. ProClin 950 is used for stabilisation. A Material safety data sheet (MSDS) is available upon request.
AEC Substrate kit is intended for immunohistochemical and in situ-hybridisation staining procedures with horse radish peroxidase (HRP). AEC (3-Amino-9-ethylcarbazol) leads to the formation of a red-brown precipitate at the location of the target antigen or target nucleic acid. The precipitate is insoluble in aqueous mounting media and can be observed by light microscopy.
15 ml AEC Chromogen (liquid AEC concentrate) 500 ml AEC Substrate Buffer
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. Do not use product after the expiry date. The working solution should be prepared freshly at the day of use. Once the two reagents are combined, the resulting solution is stable for up to three hours. Excess working solution needs to be disposed as hazardous substance. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
Add 20 µl AEC Chromogen (AEC concentrate) to 1 ml of AEC Substrate Buffer and mix thoroughly. Note: The colour intensity can be adjusted by decreasing or increasing the AEC concentration in the working solution.
Procedure:
1) Rinse the slide with wash buffer after the previous incubation step. 2) Apply the AEC working solution onto the slide. Incubate for 5-20 minutes. 3) Rinse with distilled H2O. 4) Counterstain with haematoxylin for about 30 seconds up to 5 minutes (depending on the desired staining intensity). 5) Rinse with distilled H2O. 6) Blueing in tap water for at least 5 minutes. 7) Mount with an aqueous mounting medium.
Expected results:
During the reaction of the substrate with horse radish peroxidase in presence of the chromogen AEC, a red-brown precipitate is formed at the location of the target antigen or nucleic acid. The precipitate is insoluble in aqueous solvents and can be observed by light microscopy.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). In some tissues endogenous peroxidase activity may cause non-specific staining. The enzyme activity should be blocked by incubation with hydrogen peroxide solution (H2O2 solution). The step is carried out before incubation with primary antibody but after dewaxing and rehydration. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. The coloured precipitate formed by AEC is soluble in organic solvents. The tissue sections therefore have to be counterstained with aqueous solutions (e. g. Gills or Mayers haematoxylin) and mounted with aqueous mounting media. The colour intensity of the reaction product can decrease with time, especially when exposed to light. The staining reaction itself can be influenced in the same way when carried out in strong light. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided
Precautions:
Use by qualified personnel only. Some of the reagents used in this kit are hazardous to your health. Wear protective clothing to avoid contact of reagents or specimen with eye, skin or mucous membrane. In case of a reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining may occur. Material safety data sheets (MSDS) are available upon request.
The Plus AP Kit, Broad Spectrum is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mouse, rabbit, rat, and guinea pig. The Plus AP Kit, Broad Spectrum can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Kits, Broad Spectrum is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and alkaline phosphatase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus AP Kit, Broad Spectrum is polyvalent. With this kit it is therefore possible to detect mono- and polyclonal primary antibodies and sera obtained from mouse, rabbit, rat, and guinea pig.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary or secondary antibody is minimized via incubation with a protein blocking solution (Blocking Solution provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and streptavidin-alkaline phosphatase-conjugate (Streptavidin-AP-Conjugate). A second washing is followed by the application of this conjugate. It binds to biotin at the secondary antibody. Any excess of unbound streptavidin-AP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent Red (included only in kit MON-APP110) leads to the formation of a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
4x 15 ml Blocking Solution Reagent 1 (ready-to-use) 4x 15 ml Biotinylated Secondary Antibody, polyvalent Reagent 2 (ready-to-use) 4x 15 ml Streptavidin-AP-Conjugate Reagent 3 (ready-to-use) 8 x 5 ml Permanent Red Buffer (Substrate Buffer) 2 ml Permanent Red Concentrate (Chromogen) Substrate systems recommended (if not included in the kit): Permanent AP Red Kit, BCIP/NBT Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date. It should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support .
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion.Tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate working solution (with MON-APP110 only): Add 2 drops (60 µl) of Permanent Red Concentrate to one bottle of Permanent Red Buffer (substrate buffer) and mix. This solution should be used directly after preparation.
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 2 min. 5. Biotinylated Secondary Antibody, polyvalent (Reagent 2, yellow) 10-15 min. 6. Washing with wash buffer 3 x 2 min. 7. Streptavidin-AP-Conjugate (Reagent 3, red) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent Red substrate-chromogen solution (with MON-APP110) 5 min. 10. Wash with distilled H2O 1 min. 11. Permanent Red substrate-chromogen solution (with MON-APP110) 5 min. 12. Wash with distilled H2O 3 x 1 min. 13. Counterstaining and blueing 14. Mounting: aqueous or permanent after dehydration * The incubation times should be adjusted, when using other substrate-chromogen systems.
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse, rabbit, rat or guinea pig. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolized by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see also Limitations of the procedure). 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. ProClin 300 and sodium azide (NaN3), used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) for the pure substances are available upon request. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear.
For in-vitro Diagnostic Use. The BrightVision two components detection system peroxidase Goat Anti-Mouse/Rabbit IgG AP, is intended for use in immunohistochemistry for the detection of mouse or rabbit antibodies.
The BrightVision detection system peroxidase Goat Anti- Mouse/Rabbit AP, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision detection system detects Mouse or Rabbit bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen (not provided).
Principle of method:
Two steps detection system goat anti-mouse/rabbit AP
Reagents provided:
Post-blocking (ready-to-use) 55 ml and Polymer Goat Anti-Mouse/Rabbit AP (ready-to-use) 55 ml.
Storage and handling:
2-8°C and in the dark
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary mouse or rabbit antibody (Antibody; 30 min), 8. Wash buffer (PBS or TBS buffer; 2x 5 min), 9. Detection system, step 1, post-blocking (Post-blocking; 15 min), 10. Wash buffer (PBS or TBS buffer; 2x 5 min), 11. Detection system, step 2, polymer Mouse/Rabbit AP (Labeled polymer; 30 min), 12. Wash buffer (PBS or TBS buffer; 2x 5 min), 13. If applicable Substrate (DAB), 14. Wash aqua dest (Wash; 2x 2 min), 15. Counterstain, dehydrate and coverslip (Auxiliary)
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
The Plus AP Polymer anti-Rabbit is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. It is developed for use in combination with monoand polyclonal primary antibodies and sera obtained from rabbits. The reagent can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Polymer anti-Rabbit is a highly sensitive detection reagent intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer in this kit consists of several molecules of secondary antibodies covalently bound to several molecules of alkaline phosphatase (AP). Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The reagent is suitable for the detection of mono- and polyclonal primary antibodies and sera obtained from rabbits. In contrast to other detection techniques, which often use the streptavidin-biotin system the Plus AP Polymer anti-Rabbit avoids the problem of background staining caused by endogenous biotin in the tissue.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the AP polymer is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the AP-polymer is applied and incubated. Any excess of unbound AP-polymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent AP Red leads to the formation of a magentared product of reaction at the place of the target antigen.
Reagents provided:
6 ml AP-Polymer anti-Rabbit (Ready-to-use) Substrate systems recommended: Permanent AP Red kit. Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. ? Deparaffinise and rehydrate paraffin-embedded tissue sections. ? Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. ? Tissue sections have to be completely covered with the different reagents in order to avoid drying out
Procedure:
1. Blocking Solution (protein block, this step is optional) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 5 min. 5. AP-polymer anti Rabbit 30 min. 6. Washing with wash buffer 3 x 2 min. 7. Permanent AP Red 5-15 min. (Controlling the colour intensity via light microscope is recommended.) 8. Stopping the reaction with distilled H2O when the desired colour intensity is attained 9. Counterstaining and blueing 10. Mounting: permanent or aqueous with Permanent AP Red
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support . No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from rabbit, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use a Blocking Solution or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high).
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of the reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining might appear. ProClin 950 is used for stabilisation. A Material safety data sheet (MSDS) is available upon request.
The Plus AP Kit, Rabbit is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from rabbit. The Plus AP Kit, Rabbit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Kit, Rabbit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and alkaline phosphatase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus AP Kit, Rabbit binds to rabbit primary antibodies. Therefore this kit can detect mono- and polyclonal primary antibodies and sera obtained from rabbit.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This antibody functions as a link between primary antibody and streptavidin-alkaline phosphatase-conjugate (Streptavidin-AP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-AP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent Red (included only in kit MON-APP128) leads to the formation of a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
125 ml Blocking Solution Reagent 1 (ready-to-use) 125 ml Biotinylated Secondary Antibody, Rabbit Reagent 2 (ready-to-use) 125 ml Streptavidin-AP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit) Permanent AP Red kit, BCIP/NBT Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate working solution (with MON-APP128 only): Add 2 drops (60 µl) of Permanent Red Concentrate to one bottle of Permanent Red Buffer (Substrate Buffer) and mix. This solution should be used directly after preparation.
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 2 min. 5. Biotinylated Secondary Antibody, Rabbit (Reagent 2, yellow) 10-15 min. 6. Washing with wash buffer 3 x 2 min. 7. Streptavidin-AP-Conjugate (Reagent 3, red) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent Red substrate-chromogen solution (with AP008RED-RB) 5 min. 10. Wash with distilled H2O 1 min. 11. Permanent Red substrate-chromogen solution (with AP008RED-RB) 5 min. 12. Wash with destilled water 3 x 1 min. 13. Counterstaining and blueing 14. Mounting: aqueous or permanent after dehydration * The incubation times should be adjusted, when using other substrate-chromogen systems
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from rabbit, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see section Limitations of the Procedure). 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific binding.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) for the pure substances are available upon request. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear.
Antibody Diluent B is especially developed for dilution of certain primary antibodies. Antibodies diluted with Antibody Diluent B are primarily used in immunohistochemistry with formalin-fixed paraffin-embedded tissue sections, but also with frozen, HOPE-fixed, and cytological samples as well as in immunoblot procedures.
Antibody diluents used in immunohistochemistry should protect the antibody from microbial contamination and stabilize the antibody chemically. Antibody Diluent B reduces non-specific binding of antibodies to tissue sections and is therefore extremely useful in receiving background-free staining results.
Principle of method:
Immunohistochemical staining procedures often start with incubation of a blocking solution to reduce unspecific binding of primary antibody to tissue sections. This step can be omitted if the antibody used is diluted in Antibody Diluent B. Antibody Diluent B minimises unspecific binding of the primary antibody to the tissue section, reduces surface tension of the antibody solution and improves spreading the reagent on the slide, increases microbial and chemical stability of the antibody, reduces adhesion of antibody to the surface of the vial, and minimises the danger of antibody degradation by proteolytic enzymes.
Reagents provided:
25 ml Antibody Diluent B (ready-to-use)
Storage and handling:
The solution should be stored at 2-8°C without furt her dilution. Do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. If stored at room temperature the solution is stable for at least 10 month from the date of delivery. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, contact our technical support. Also refer to the instructions of the detection systems containing Peroxide Block for guidance on general troubleshooting
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results.Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent or specimen with eye, skin or mucous membrane. In case of the reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. (NaN3), used for stabilisation, is not considered hazardous material in the concentration used. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. A material safety data sheet (MSDS) is available upon request.
Trypsin Pretreatment Kit consists of 2 reagents for the preparation of a trypsin solution used for enzymatic epitope retrieval on formalin-fixed tissue sections on slides. This procedure (sometimes called PIER, Protease Induced Epitope Retrieval) is primarily used in immunohistochemical staining procedures. Trypsin Pretreatment Kit is for research use only.
Immunohistochemical staining procedures consist of sequential incubation steps with blocking solutions, antibodies and secondary reagents, enzymes and chromogenic substrates carried out on tissue sections. These tissue sections are mostly prepared out of formalin-fixed paraffin-embedded tissue blocks. Cellular structures are very effectively stabilised by formalin fixation which results in optimal morphological preservation of the sample. On the other hand the formalin fixation leads to strong cross-links between proteins. This means that epitopes of antigens are being masked and often are no longer accessible for primary antibodies. In order to enable primary antibodies to bind to antigens the epitopes have to be recovered. Enzymatic digestion with proteolytic enzymes (PIER) restores structures of the epitopes making them more accessible to specific antibodies. Heat induced epitope retrieval (HIER) in buffer solutions of different compositions and pH-values is another way of recovering epitopes. The primary antibody used determines the appropriate method.
Principle of method:
The components of this Trypsin Pretreatment Kit allow for the preparation of a buffered trypsin solution for enzymatic epitope retrieval.
Reagents provided:
30 ml Trypsin Solution 125 ml Trypsin Buffer
Storage and handling:
The solutions should be stored at 2-8°C. Please sto re the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. Do not use product after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Reagent preparation:
Mix 1 part Trypsin Solution with 3 parts Trypsin Buffer. The activity of the resulting trypsin solution can be adjusted by variation of the mixing ratio. Mix the two components in the ratio 1:1 when strong epitope retrieval is desired. The working solution is stable for at least one week if stored at 2-8°C.
Procedure:
Trypsin Pretreatment Kit is suitable for enzymatic epitope retrieval carried out after the dewaxing and rehydration of the sections. 1. Cover deparaffinised and rehydrated tissue sections with trypsin working solution. 2. Incubate for 10 - 20 minutes at 37°C. 3. Rinse carefully (3 x) with wash buffer. 4. Proceed with immunohistological staining as usual.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent and specimen with eye, skin or mucous membranes. In case of reagent or specimen coming into contact with a sensitive area, wash area with large amounts of water. A material safety data sheet (MSDS) is available upon request.
The Plus AP Kit, Rabbit is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from rabbit. The Plus AP Kit, Rabbit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Kit, Rabbit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and alkaline phosphatase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus AP Kit, Rabbit binds to rabbit primary antibodies. Therefore this kit can detect mono- and polyclonal primary antibodies and sera obtained from rabbit.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This antibody functions as a link between primary antibody and streptavidin-alkaline phosphatase-conjugate (Streptavidin-AP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-AP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent Red (included only in kit MON-APP128) leads to the formation of a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
500 ml Blocking Solution Reagent 1 (ready-to-use) 500 ml Biotinylated Secondary Antibody, Rabbit Reagent 2 (ready-to-use) 500 ml Streptavidin-AP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit) Permanent AP Red kit, BCIP/NBT Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate working solution (with MON-APP128 only): Add 2 drops (60 µl) of Permanent Red Concentrate to one bottle of Permanent Red Buffer (Substrate Buffer) and mix. This solution should be used directly after preparation.
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 2 min. 5. Biotinylated Secondary Antibody, Rabbit (Reagent 2, yellow) 10-15 min. 6. Washing with wash buffer 3 x 2 min. 7. Streptavidin-AP-Conjugate (Reagent 3, red) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent Red substrate-chromogen solution (with AP008RED-RB) 5 min. 10. Wash with distilled H2O 1 min. 11. Permanent Red substrate-chromogen solution (with AP008RED-RB) 5 min. 12. Wash with destilled water 3 x 1 min. 13. Counterstaining and blueing 14. Mounting: aqueous or permanent after dehydration * The incubation times should be adjusted, when using other substrate-chromogen systems
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from rabbit, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see section Limitations of the Procedure). 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific binding.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) for the pure substances are available upon request. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear.
The Plus AP Kit, Mouse is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with monoclonal primary antibodies and sera obtained from mice. The Plus AP Kit, Mouse can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Kit, Mouse is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and alkaline phosphatase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus AP Kit, Mouse binds to mouse primary antibodies. Therefore this kit can detect monoclonal primary antibodies and sera obtained from mice.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and the streptavidinalkaline phosphatase-conjugate (Streptavidin-AP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-AP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent Red (included only in kit MON-APP119) leads to a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
125 ml Blocking Solution Reagent 1 (ready-to-use) 125 ml Biotinylated Secondary Antibody, Mouse Reagent 2 (ready-to-use) 125 ml Streptavidin-AP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit): Permanent AP Red Kit, BCIP/NBT Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate working solution (with MON-APP119 only): Add 2 drops (60 µl) of Permanent Red Concentrate to one bottle of Permanent Red Buffer (Substrate Buffer) and mix. This solution should be used directly after preparation.
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 2 min. 5. Biotinylated Secondary Antibody, Mouse (Reagent 2, yellow) 10-15 min. 6. Washing with wash buffer 3 x 2 min. 7. Streptavidin-AP-Conjugate (Reagent 3, red) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent Red substrate-chromogen solution (with MON-APP119) 5 min. 10. Wash with distilled H2O 1 min. 11. Permanent Red substrate-chromogen solution (with MON-APP119) 5 min. 12. Wash with destilled water 3 x 1 min. 13. Counterstaining and blueing 14. Mounting: aqueous or permanent after dehydration * The incubation times should be adjusted, when using other substrate-chromogen systems.
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support . No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see section Limitations of the Procedure). 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) for the pure substances are available upon request. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear
The BrightDiluents universal IHC diluent is specially formulated to stabilize antibodies and eliminate backgrounds encountered in immunohistochemistry staining procedures. The diluent contains complex proteins and non-protein mixtures which eliminate histostaining background by blocking Fc receptors and prevents non-specific protein-protein interactions. It can also be used as blocking applied before primary antibodies. If primary antibodies are diluted in this diluent, a blocking step before primary antibodies can generally be omitted. The blocking /diluent solution is supplied in Ready-to-Use format. It should not be diluted to be effective. The diluent contains no azide, therefore, it can be used to dilute and stabilize HRP-conjugates as well as any other solution that need and stabilizing carrier protein, such as Blocking and Poly-AP conjugates. This product should be interpreted by a qualified pathologist with relevant clinical information, morphological and histological studies and with proper controls. The ready-to-use antibody diluent is available in different colors: MON-APP917 (Transparant/colorless), MON-APP917B (Blue), MON-APP917Y (Yellow), MON-APP917G (green), MON-APP917R (Red)
Principle of method:
Antibody diluent
Reagents provided:
125 ml BrightDiluent, normal antibody diluent (ready-to-use)
For in-vitro Diagnostic Use. The BrightVision one step detection system peroxidase Goat Anti-Mouse IgG HRP, is intended for use in immunohistochemistry for the detection of mouse antibodies.
The BrightVision detection system peroxidase Goat Anti- Mouse HRP, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision detection system detects Mouse bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen (not provided). Also available in 110 ml, 500 ml and 1000 ml.
Principle of method:
One step detection system peroxidase goat anti-mouse IgG HRP
Reagents provided:
One step detection system Goat anti-Mouse HRP (Ready-to-use; 55 ml)
Storage and handling:
2-8°C and in the dark
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary mouse antibody (Antibody; 30 min), 8. Wash buffer (PBS or TBS buffer; 2x 5 min), 9. Detection system, step 1, polymer Mouse, (Labeled polymer; 30 min), 10. Wash buffer (PBS or TBS buffer; 2x 5 min), 11. Substrate (DAB; see applicable IFU), 12. Wash aqua dest (Wash; 2x 2 min), 13. Counterstain, dehydrate and coverslip (Auxiliary)
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
The Plus AP Kit, Broad Spectrum is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mouse, rabbit, rat, and guinea pig. The Plus AP Kit, Broad Spectrum can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Kits, Broad Spectrum is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and alkaline phosphatase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus AP Kit, Broad Spectrum is polyvalent. With this kit it is therefore possible to detect mono- and polyclonal primary antibodies and sera obtained from mouse, rabbit, rat, and guinea pig.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary or secondary antibody is minimized via incubation with a protein blocking solution (Blocking Solution provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and streptavidin-alkaline phosphatase-conjugate (Streptavidin-AP-Conjugate). A second washing is followed by the application of this conjugate. It binds to biotin at the secondary antibody. Any excess of unbound streptavidin-AP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent Red (included only in kit MON-APP110) leads to the formation of a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
125 ml Blocking Solution Reagent 1 (ready-to-use) 125 ml Biotinylated Secondary Antibody, polyvalent Reagent 2 (ready-to-use) 125 ml Streptavidin-AP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit): Permanent AP Red Kit, BCIP/NBT Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date. It should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support .
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion.Tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate working solution (with MON-APP110 only): Add 2 drops (60 µl) of Permanent Red Concentrate to one bottle of Permanent Red Buffer (substrate buffer) and mix. This solution should be used directly after preparation.
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 2 min. 5. Biotinylated Secondary Antibody, polyvalent (Reagent 2, yellow) 10-15 min. 6. Washing with wash buffer 3 x 2 min. 7. Streptavidin-AP-Conjugate (Reagent 3, red) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent Red substrate-chromogen solution (with MON-APP110) 5 min. 10. Wash with distilled H2O 1 min. 11. Permanent Red substrate-chromogen solution (with MON-APP110) 5 min. 12. Wash with distilled H2O 3 x 1 min. 13. Counterstaining and blueing 14. Mounting: aqueous or permanent after dehydration * The incubation times should be adjusted, when using other substrate-chromogen systems.
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse, rabbit, rat or guinea pig. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolized by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see also Limitations of the procedure). 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. ProClin 300 and sodium azide (NaN3), used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) for the pure substances are available upon request. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear.
CryoCompound freezing medium is an aqueous based frozen tissue embedding medium designed to support tissue blocks in cryostat sectioning. Formulated to promote rapid freezing, enhanced sectioning and consistent results at a working temperature of -20° C. The ready-to-use Cryocompound is available in different colors: MON-APP900C (Transparant/colorless), MON-APP900B (Blue), MON-APP900Y (Yellow), MON-APP900O (Orange), MON-APP900G (green), MON-APP900R (Red) or Multicolorkit MON-APP900BYGR (Blue, Yellow, Green, Red).
Principle of method:
Freezing medium
Reagents provided:
100 ml Cryocompound, freezing medium (ready-to-use)
Storage and handling:
Store at room temperature
Procedure:
1. Place few drops of CryoCompound (depends on the size of the sample to be embedded) onto the center of the bottom of cryomold. Be careful to select the proper size embedding mold according to the size of the sample to be embedded. 2. Try to avoid the formation of air bubbles. Remove any bubbles inside the CryoCopound. This is important because the air bubbles will create problems when cutting sections. Air bubbles create freeze- thaw-freeze cycle and ice crystal will form inside of it and result in a very bad morphology due to the ice crystal artefact. 3. Let it settle for 15-30 seconds to allow the CryoCompound to completely wet the surface of the tissue. Hardening of the CryoCompound included the sample (it will happen in 0.5-1 minute) before preparing the CryoCompoundsample-block.
The Plus HRP Polymer Kit is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. It is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mice and rabbits. The kit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Polymer Kit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer in this kit consists of several molecules of secondary antibodies covalently bound to several molecules of horse radish peroxidase (HRP). Visualisation occurs via an enzyme-substrate reaction in the presence of a colorising reagent which permits microscopical analysis. The test system is suitable for the detection of mono- and polyclonal primary antibodies and sera obtained from mice and rabbits. In contrast to other detection techniques, which often use the streptavidin-biotin system the Plus HRP Polymer Kit avoids the problem of background staining caused by endogenous biotin in the tissue
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (peroxide block). Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the HRPpolymer is minimized by incubation with a protein blocking solution (Blocking Solution, provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the enhancement reagent (PostBlock) is applied and incubated. A second washing is followed by the application of the HRP-polymer. Any excess of unbound HRP-polymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB forms a dark brown precipitate.
Reagents provided:
100 ml Blocking Solution Reagent 1 (ready-to-use) 100 ml PostBlock Reagent 2 (ready-to-use) 100 ml HRP-Polymer (Mouse/Rabbit) Reagent 3 (ready-to-use) Substrate systems recommended: Permanent AEC kit, AEC single solution, AEC substrate kit, DAB substrate kit, DAB High contrast kit. Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support.
Reagent preparation:
Reagents should be at room temperature when used. ? Deparaffinise and rehydrate paraffin-embedded tissue sections. ? Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. ? Tissue sections have to be completely covered with the different reagents in order to avoid drying out.
Procedure:
1. Peroxide blocking (3 % H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 5 min. 7. PostBlock (Reagent 2, yellow) 20 min. 8. Washing with wash buffer 3 x 5 min. 9. HRP-polymer (Reagent 3, red) 30 min. 10. Washing with wash buffer 3 x 2 min. 11. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 12. Stopping the reaction with distilled H2O when the desired colour intensity is attained 13. Counterstaining and blueing 14. Mounting: aqueous with AEC, permanent with DAB
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support . No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse or rabbit, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Nonspecific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase in the tissue. Maybe the hydrogen peroxide solution used for blocking was inactivated.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity may cause non-specific staining. The enzyme activity is blocked by incubation with hydrogen peroxide solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. We guarantee that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin is used for stabilisation. A material safety data sheet is available upon request.
The Plus HRP Kit, Rabbit is based on the streptavidin-biotin system. It is designed for qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from rabbit. The Plus HRP Kit, Rabbit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Kit, Rabbit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and horse radish peroxidase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus HRP Kit, Rabbit binds to rabbit primary antibodies. Therefore this kit can detect mono- and polyclonal primary antibodies and sera obtained from rabbit.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide Block). Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This antibody functions as a link between primary antibody and the streptavidin-horse radish peroxidase-conjugate (Streptavidin-HRP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-HRPconjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC (included only in kit MON-APP132) leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB (included only in kit MON-APP133) forms a dark brown precipitate.
Reagents provided:
125 ml Blocking Solution Reagent 1 (ready-to-use) 125 ml Biotinylated Secondary Antibody, Rabbit Reagent 2 (ready-to-use) 125 ml Streptavidin-HRP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit): Permanent AEC kit, AEC Single Solution, AEC substrate kit, DAB Substrate kit, DAB High Contrast kit Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Procedure:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. The tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate AEC working solution (with MON-APP132 only): Add 2 drops (100 µl) of AEC Concentrate to one bottle of AEC Substrate Buffer and mix thoroughly. Preparation of the chromogenic substrate DAB working solution (with MON-APP133 only): Add 4 drops (200 µl) of DAB Concentrate to one bottle of DAB Substrate Buffer and mix thoroughly.
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from rabbit. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase. Maybe the hydrogen peroxide solution used for blocking was inactivated. 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with 3% H2O2 solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Background staining due to endogenous biotin can be blocked through an avidinbiotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) are available upon request.
Permanent AEC Kit is intended for immunohistochemical and in situ-hybridisation staining procedures with horse radish peroxidase (HRP). AEC (3-Amino-9-ethylcarbazol) leads to the formation of a red-brown precipitate at the location of the target antigen or target nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light microscopy. Permanent AEC Kit is intended for research use only.
5.5 ml Reagent 1 3 ml Reagent 2 3 ml Reagent 3 (Chromogen) 4.5 ml Reagent 4 (H2O2) 1 Dilution Vial
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. Do not use product after the expiry date. The working solution should be prepared freshly at the day of use. Excess working solution should be disposed. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
1) Pipette 5 ml distilled or deionised water into the provided dilution vial. 2) Add 3 drops buffer concentrate (Reagent 1). Mix thoroughly. 3) Add 2 drops Reagent 2. Mix thoroughly. 4) Add 2 drops AEC chromogen (Reagent 3). Mix thoroughly. 5) Add 2 drops H2O2 substrate (Reagent 4). Mix thoroughly. This working solution is stable for at least 16 hours if stored at 2-8°C in a dark place.
Procedure:
1) Apply the Permanent AEC working solution onto the slide. Incubate for 5-15 minutes. (Incubation time can be extended, if desired.) 2) Rinse with distilled or deionised H2O. 3) Counterstain with haematoxylin for about 30 seconds up to 5 minutes (depending on the desired staining intensity). 4) Rinse with distilled or deionised H2O. 5) Blueing in tap water for at least 5 minutes. 6) Dehydrate through a graded series of ethanol and clear in xylene. Mount with a permanent mounting medium.
Expected results:
During the reaction of the substrate with horse radish peroxidase in presence of the chromogen AEC, a red-brown precipitate is formed at the location of the target antigen or nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light microscopy.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). In some tissues endogenous peroxidase activity may cause non-specific staining. The enzyme activity should be blocked by incubation with hydrogen peroxide solution (H2O2 solution). The step is carried out before incubation with primary antibody but after dewaxing and rehydration. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. A longer exposure to absolute ethanol can result in decreasing staining intensity. Use of recycled alcohol to dehydrate tissue slides after staining is not recommended. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagents or specimen with eye, skin or mucous membrane. In case of a reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining may occur. A material safety data sheet (MSDS) is available upon request.
DAB Substrate kit High Contrast is developed for immunohistochemical and in situ-hybridisation staining procedures with horse radish peroxidase (HRP). DAB (3,3-Diaminobenzidine) leads to the formation of a brown precipitate at the location of the target antigen or target nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light microscopy. The kit is especially useful when a high contrast between chromogen and counter stain is desired. Compared to standard DAB staining systems the DAB Substrate High Contrast kit gives a darker brown colour and a higher sensitivity.
30 ml DAB Chromogen (liquid DAB concentrate) 500 ml DAB Substrate Buffer High Contrast
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. Do not use product after the expiry date. The working solution should be prepared freshly at the day of use. Once the two reagents are combined, the resulting solution is stable for up to six hours. Excess working solution should be disposed as hazardous substance. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
Add 50 µl of DAB Chromogen (DAB concentrate) to 1 ml of DAB Substrate Buffer High Contrast and mix thoroughly. Note: Typical working concentrations are 50 µl (0.9 mg) DAB per ml substrate buffer. The colour intensity can be adjusted by decreasing or increasing the DAB concentration in the working solution. Maximum sensitivity in immunohistochemical staining can be achieved by working concentrations of about 80 µl (1.5 mg) DAB per ml substrate buffer.
Procedure:
1) Rinse the slide with wash buffer after the previous incubation step. 2) Apply the DAB High contrast working solution to the slide. Incubate for 5-15 minutes. 3) Rinse with distilled H2O. 4) Counterstain with haematoxylin for about 30 seconds up to 5 minutes (depending on the desired staining intensity). 5) Rinse with distilled H2O. 6) Blueing in tap water for at least 5 minutes. 7) Dehydrate through a graded series of ethanol and clear in xylene. Mount with a permanent mounting medium. Note: It is also possible to mount DAB High Contrast with aqueous mounting media.
Expected results:
During the reaction of the substrate with horse radish peroxidase in presence of the chromogen DAB, a brown precipitate is formed at the location of the target antigen or nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light microscopy.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). In some tissues endogenous peroxidase activity may cause non-specific staining. The enzyme activity should be blocked by incubation with hydrogen peroxide solution (H2O2 solution). The step is carried out before incubation with primary antibody but after dewaxing and rehydration. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. The DAB chromogen is hazardous to your health. Wear protective clothing to avoid contact of reagents or specimen with eye, skin or mucous membrane. In case of a reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining may occur. Material safety data sheets (MSDS) are available upon request.
The Fast AP One-Step Polymer anti-Mouse/Rabbit is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. It was developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mice or rabbit. The kit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE. It is intended for in vitro diagnostic use.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Fast AP One-Step Polymer anti-Mouse/Rabbit is a highly sensitive detection reagent intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer consists of several molecules of secondary antibodies covalently bound to several molecules of alkaline phosphatase (AP). Visualisation occurs via an enzymesubstrate reaction in the presence of a colorising reagent which permits microscopical analysis. The test system is suitable for the detection of mono- and polyclonal primary antibodies and sera obtained from mice or rabbit. Cross-reactivity with primary antibodies from rat has been observed. In contrast to other detection techniques, which often use the streptavidin-biotin system the Fast AP One-Step Polymer anti-Mouse/Rabbit avoids the problem of background staining caused by endogenous biotin in the tissue.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the AP OneStep Polymer is minimized by incubation with a protein blocking solution. This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the AP One-Step Polymer is applied and incubated. Any excess of unbound polymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent AP Red leads to the formation of a magentared product of reaction at the place of the target antigen.
Reagents provided:
100 ml Fast AP One-Step Polymer anti-Mouse/Rabbit (ready-to-use) Substrate systems recommended: Permanaent AP Red kit Materials required but not supplied Positive and negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS Blocking Solution (for protein blocking, optional) Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date. It should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagent, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out.
Procedure:
1. Blocking Solution (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 5 min. 5. AP One-Step Polymer anti-Mouse/Rabbit 30 Min. 6. Washing with wash buffer 3 x 2 min. 7. Permanent AP Red, 10-20 min. (Controlling the colour intensity via light microscope is recommended.) 8. Stopping the reaction with distilled H2O when the desired colour intensity is attained 9. Counterstaining and blueing 10. Mounting: permanent or aqueous with Permanent AP Red Kit
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse or rabbit but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Nonspecific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use Blocking Solution or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high).
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 is used for stabilisation. A Material safety data sheet (MSDS) is available upon request.
AEC Substrate kit is intended for immunohistochemical and in situ-hybridisation staining procedures with horse radish peroxidase (HRP). AEC (3-Amino-9-ethylcarbazol) leads to the formation of a red-brown precipitate at the location of the target antigen or target nucleic acid. The precipitate is insoluble in aqueous mounting media and can be observed by light microscopy.
3 ml AEC Chromogen (liquid AEC concentrate) 11 x 5 ml AEC Substrate Buffer
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. Do not use product after the expiry date. The working solution should be prepared freshly at the day of use. Once the two reagents are combined, the resulting solution is stable for up to three hours. Excess working solution needs to be disposed as hazardous substance. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
Add 2 drops of AEC Chromogen (AEC concentrate) to one bottle of AEC Substrate Buffer and mix thoroughly.
Procedure:
1) Rinse the slide with wash buffer after the previous incubation step. 2) Apply the AEC working solution onto the slide. Incubate for 5-20 minutes. 3) Rinse with distilled H2O. 4) Counterstain with haematoxylin for about 30 seconds up to 5 minutes (depending on the desired staining intensity). 5) Rinse with distilled H2O. 6) Blueing in tap water for at least 5 minutes. 7) Mount with an aqueous mounting medium.
Expected results:
During the reaction of the substrate with horse radish peroxidase in presence of the chromogen AEC, a red-brown precipitate is formed at the location of the target antigen or nucleic acid. The precipitate is insoluble in aqueous solvents and can be observed by light microscopy.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). In some tissues endogenous peroxidase activity may cause non-specific staining. The enzyme activity should be blocked by incubation with hydrogen peroxide solution (H2O2 solution). The step is carried out before incubation with primary antibody but after dewaxing and rehydration. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. The coloured precipitate formed by AEC is soluble in organic solvents. The tissue sections therefore have to be counterstained with aqueous solutions (e. g. Gills or Mayers haematoxylin) and mounted with aqueous mounting media. The colour intensity of the reaction product can decrease with time, especially when exposed to light. The staining reaction itself can be influenced in the same way when carried out in strong light. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided
Precautions:
Use by qualified personnel only. Some of the reagents used in this kit are hazardous to your health. Wear protective clothing to avoid contact of reagents or specimen with eye, skin or mucous membrane. In case of a reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining may occur. Material safety data sheets (MSDS) are available upon request.
Paraformaldehyde (PFA) is the polymerization product of formaldehyde with a typical degree of polymerization of 8100 units. Paraformaldehyde is not a fixative itself; it must be depolymerized to formaldehyde in solution. In cell culture, a typical formaldehyde fixing procedure would involve using a 4% formaldehyde solution in phosphate buffered saline (PBS) on ice for 10 minutes. Fixing ensures that sample cell structures stay intact and that antigens are immobilized, while ideally still permitting unfettered access of antibodies to target antigens. CAS 30525-89-4, soluble in water, pH 7.0-7.6 at 25°C. The solution should be clear, colorless, with no precipitate.
Principle of method:
Fixing cells for immunohistochemistry (IHC)
Reagents provided:
500 ml 4 % Paraformaldehyde (PFA) solution in PBS
Storage and handling:
Store at -20°C for one year
Trouble shooting:
Adjust pH to 7.2-7.6 with NaH2PO4 if pH
Precautions:
Causes serious eye damage. Suspected of causing cancer. May cause an allergic skin reaction. Causes skin irritation. Avoid breathing dust/fume/gas/mist/vapors/spray. Wear protective gloves/protective clothing/eye protection/face protection. Use personal protective equipment as required. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Store locked up. Dispose of contents/container in accordance with local/regional/national/international regulations
Antibody Diluent is developed for dilution of primary antibodies. Antibodies diluted with Antibody Diluent are primarily used in immunohistochemistry with formalin-fixed paraffin-embedded tissue sections, but also with frozen, HOPE-fixed, and cytological samples as well as in immunoblot procedures.
Antibody diluents used in immunohistochemistry should protect the antibody from microbial contamination and stabilize the antibody chemically. Antibody Diluent reduces non-specific binding of antibodies to tissue sections and is therefore extremely useful in receiving background-free staining results.
Principle of method:
Immunohistochemical staining procedures often start with incubation of a blocking solution to reduce unspecific binding of primary antibody to tissue sections. This step can be omitted if the antibody used is diluted in Antibody Diluent. Antibody Diluent ? minimises unspecific binding of the primary antibody to the tissue section, ? reduces surface tension of the antibody solution and improves spreading the reagent on the slide, ? increases microbial and chemical stability of the antibody, ? reduces adhesion of antibody to the surface of the vial, ? and minimises the danger of antibody degradation by proteolytic enzymes.
Reagents provided:
500 ml Antibody Diluent (ready-to-use)
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. If stored at room temperature the solution is stable for at least 10 month from the date of delivery. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, contact our technical support. Also refer to the instructions of the detection systems containing Peroxide Block for guidance on general troubleshooting
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use through qualified personnel only. Wear protective clothing to avoid contact of reagents and specimens with eye, skin and mucous membranes. If reagents or specimens come in contact with sensitive area, wash with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. ProClin300 and sodium azide (NaN3) are used for stabilisation. Reaction of sodium azide with lead or copper in drainage pipes can result in the formation of highly explosive metallic azides. Discard the antibody solution in a large volume of running water to avoid formation of deposits. A material safety data sheet (MSDS) for the pure substances is available upon request.
The Plus HRP Kit, Rabbit is based on the streptavidin-biotin system. It is designed for qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from rabbit. The Plus HRP Kit, Rabbit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Kit, Rabbit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and horse radish peroxidase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus HRP Kit, Rabbit binds to rabbit primary antibodies. Therefore this kit can detect mono- and polyclonal primary antibodies and sera obtained from rabbit.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide Block). Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This antibody functions as a link between primary antibody and the streptavidin-horse radish peroxidase-conjugate (Streptavidin-HRP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-HRPconjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC (included only in kit MON-APP132) leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB (included only in kit MON-APP133) forms a dark brown precipitate.
Reagents provided:
8 ml Peroxide Block (ready-to-use) 8 ml Blocking Solution Reagent 1 (ready-to-use) 8 ml Biotinylated Secondary Antibody, Rabbit Reagent 2 (ready-to-use) 8 ml Streptavidin-HRP-Conjugate Reagent 3 (ready-to-use) 7 x 5 ml DAB Substrate Buffer 3 ml DAB Concentrate (Chromogen) Substrate systems recommended (if not included in the kit): Permanent AEC kit, AEC Single Solution, AEC substrate kit, DAB Substrate kit, DAB High Contrast kit Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Procedure:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. The tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate AEC working solution (with MON-APP132 only): Add 2 drops (100 µl) of AEC Concentrate to one bottle of AEC Substrate Buffer and mix thoroughly. Preparation of the chromogenic substrate DAB working solution (with MON-APP133 only): Add 4 drops (200 µl) of DAB Concentrate to one bottle of DAB Substrate Buffer and mix thoroughly.
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from rabbit. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase. Maybe the hydrogen peroxide solution used for blocking was inactivated. 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with 3% H2O2 solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Background staining due to endogenous biotin can be blocked through an avidinbiotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) are available upon request.
The Plus AP Kit, Mouse is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with monoclonal primary antibodies and sera obtained from mice. The Plus AP Kit, Mouse can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Kit, Mouse is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and alkaline phosphatase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus AP Kit, Mouse binds to mouse primary antibodies. Therefore this kit can detect monoclonal primary antibodies and sera obtained from mice.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and the streptavidinalkaline phosphatase-conjugate (Streptavidin-AP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-AP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent Red (included only in kit MON-APP119) leads to a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
500 ml Blocking Solution Reagent 1 (ready-to-use) 500 ml Biotinylated Secondary Antibody, Mouse Reagent 2 (ready-to-use) 500 ml Streptavidin-AP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit): Permanent AP Red Kit, BCIP/NBT Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate working solution (with MON-APP119 only): Add 2 drops (60 µl) of Permanent Red Concentrate to one bottle of Permanent Red Buffer (Substrate Buffer) and mix. This solution should be used directly after preparation.
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 2 min. 5. Biotinylated Secondary Antibody, Mouse (Reagent 2, yellow) 10-15 min. 6. Washing with wash buffer 3 x 2 min. 7. Streptavidin-AP-Conjugate (Reagent 3, red) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent Red substrate-chromogen solution (with MON-APP119) 5 min. 10. Wash with distilled H2O 1 min. 11. Permanent Red substrate-chromogen solution (with MON-APP119) 5 min. 12. Wash with destilled water 3 x 1 min. 13. Counterstaining and blueing 14. Mounting: aqueous or permanent after dehydration * The incubation times should be adjusted, when using other substrate-chromogen systems.
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support . No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see section Limitations of the Procedure). 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) for the pure substances are available upon request. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear
CryoCompound freezing medium is an aqueous based frozen tissue embedding medium designed to support tissue blocks in cryostat sectioning. Formulated to promote rapid freezing, enhanced sectioning and consistent results at a working temperature of -20° C. The ready-to-use Cryocompound is available in different colors: MON-APP900C (Transparant/colorless), MON-APP900B (Blue), MON-APP900Y (Yellow), MON-APP900O (Orange), MON-APP900G (green), MON-APP900R (Red) or Multicolorkit MON-APP900BYGR (Blue, Yellow, Green, Red).
Principle of method:
Freezing medium
Reagents provided:
100 ml Cryocompound, freezing medium (ready-to-use)
Storage and handling:
Store at room temperature
Procedure:
1. Place few drops of CryoCompound (depends on the size of the sample to be embedded) onto the center of the bottom of cryomold. Be careful to select the proper size embedding mold according to the size of the sample to be embedded. 2. Try to avoid the formation of air bubbles. Remove any bubbles inside the CryoCopound. This is important because the air bubbles will create problems when cutting sections. Air bubbles create freeze- thaw-freeze cycle and ice crystal will form inside of it and result in a very bad morphology due to the ice crystal artefact. 3. Let it settle for 15-30 seconds to allow the CryoCompound to completely wet the surface of the tissue. Hardening of the CryoCompound included the sample (it will happen in 0.5-1 minute) before preparing the CryoCompoundsample-block.
The Plus AP Kit, Broad Spectrum is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mouse, rabbit, rat, and guinea pig. The Plus AP Kit, Broad Spectrum can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Kits, Broad Spectrum is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and alkaline phosphatase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus AP Kit, Broad Spectrum is polyvalent. With this kit it is therefore possible to detect mono- and polyclonal primary antibodies and sera obtained from mouse, rabbit, rat, and guinea pig.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary or secondary antibody is minimized via incubation with a protein blocking solution (Blocking Solution provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and streptavidin-alkaline phosphatase-conjugate (Streptavidin-AP-Conjugate). A second washing is followed by the application of this conjugate. It binds to biotin at the secondary antibody. Any excess of unbound streptavidin-AP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent Red (included only in kit MON-APP110) leads to the formation of a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
8 ml Blocking Solution Reagent 1 (ready-to-use) 8 ml Biotinylated Secondary Antibody, polyvalent Reagent 2 (ready-to-use) 8 ml Streptavidin-AP-Conjugate Reagent 3 (ready-to-use) 8 x 5 ml Permanent Red Buffer (Substrate Buffer) 2 ml Permanent Red Concentrate (Chromogen) Substrate systems recommended (if not included in the kit): Permanent AP Red Kit, BCIP/NBT Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date. It should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support .
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion.Tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate working solution (with MON-APP110 only): Add 2 drops (60 µl) of Permanent Red Concentrate to one bottle of Permanent Red Buffer (substrate buffer) and mix. This solution should be used directly after preparation.
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 2 min. 5. Biotinylated Secondary Antibody, polyvalent (Reagent 2, yellow) 10-15 min. 6. Washing with wash buffer 3 x 2 min. 7. Streptavidin-AP-Conjugate (Reagent 3, red) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent Red substrate-chromogen solution (with MON-APP110) 5 min. 10. Wash with distilled H2O 1 min. 11. Permanent Red substrate-chromogen solution (with MON-APP110) 5 min. 12. Wash with distilled H2O 3 x 1 min. 13. Counterstaining and blueing 14. Mounting: aqueous or permanent after dehydration * The incubation times should be adjusted, when using other substrate-chromogen systems.
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse, rabbit, rat or guinea pig. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolized by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see also Limitations of the procedure). 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. ProClin 300 and sodium azide (NaN3), used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) for the pure substances are available upon request. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear.
The TRIS/EDTA buffer, is designed for use during heat-induced epitope retrieval (HIER) on formalinfixed paraffin-embedded tissue sections prior to antibody application. In immunohistochemistry (IHC), protein cross-links are formed during formalin or other aldehyde fixation. These cross-links mask the antigenic sites in tissue specimens and results in weak or false negative staining in immunohistochemical detection of proteins. The use of this citrate buffer in combination with heat ensures that the antigenicity of proteins modified, thus enhancing staining intensity of antibodies. For the recommended pre-treatment technique, please refer to the individual antibody's instructions for use. This buffer is a 10x concentrate solution and must be diluted 1:10 with deionized water before using. The final readyto-use solution should have a pH of 9.0 ± 0.3. The buffer can be used for a maximum of three runs within five days after dilution. Also available in 250 ml, 500 ml en 1000 ml.
Before use dilute 1:10 with deionized water. The final ready-to-use solution should have a pH of 9.0 ± 0,3,
Procedure:
1. Deparaffinize and rehydrate the tissue slides. 2. Fill the PT Module tank with 150 ml of TRIS?EDTA buffer and 1,350 ml of deionized water, to obtain 1,500 ml of ready-to-use solution (1:10 dilution). 3. Pre-heat the PT Module until temperature reaches 65°C and place the formalin-fixed slides in slide racks into the PT Module tank. 4. Heat the TRIS/EDTA buffer and slides to 98°C and incubate for 15 minutes. 5. Cool slides in the PT Module to 65°C. 6. Remove slides and cool to room temperature for at least 5 minutes in a PBS or TBS based buffer. 7. Continue with staining according to IHC protocol. Note: Alternative heating sources, such as a microwave or a pressure cooker, can be used to replace the PT Module tank. The optimal incubation time for these heating sources should be determined by authorised personnel / researchers.
CryoCompound freezing medium is an aqueous based frozen tissue embedding medium designed to support tissue blocks in cryostat sectioning. Formulated to promote rapid freezing, enhanced sectioning and consistent results at a working temperature of -20° C. The ready-to-use Cryocompound is available in different colors: MON-APP900C (Transparant/colorless), MON-APP900B (Blue), MON-APP900Y (Yellow), MON-APP900O (Orange), MON-APP900G (green), MON-APP900R (Red) or Multicolorkit MON-APP900BYGR (Blue, Yellow, Green, Red).
Principle of method:
Freezing medium
Reagents provided:
100 ml Cryocompound, freezing medium (ready-to-use)
Storage and handling:
Store at room temperature
Procedure:
1. Place few drops of CryoCompound (depends on the size of the sample to be embedded) onto the center of the bottom of cryomold. Be careful to select the proper size embedding mold according to the size of the sample to be embedded. 2. Try to avoid the formation of air bubbles. Remove any bubbles inside the CryoCopound. This is important because the air bubbles will create problems when cutting sections. Air bubbles create freeze- thaw-freeze cycle and ice crystal will form inside of it and result in a very bad morphology due to the ice crystal artefact. 3. Let it settle for 15-30 seconds to allow the CryoCompound to completely wet the surface of the tissue. Hardening of the CryoCompound included the sample (it will happen in 0.5-1 minute) before preparing the CryoCompoundsample-block.
The Plus HRP Polymer anti-Rabbit is designed for the qualitative detection of antigens in fixed paraffinembedded tissue sections, in frozen tissue sections, and in cytological samples. It is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from rabbits. The reagent can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Polymer anti-Rabbit is a highly sensitive detection reagent intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer in this kit consists of several molecules of secondary antibodies covalently bound to several molecules of horse radish peroxidase (HRP). Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The reagent is suitable for the detection of mono- and polyclonal primary antibodies and sera obtained from rabbits. In contrast to other detection techniques, which often use the streptavidin-biotin system the Plus HRP Polymer anti-Rabbit avoids the problem of background staining caused by endogenous biotin in the tissue.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide block). Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the HRP polymer is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the HRP-polymer is applied and incubated. Any excess of unbound HRP-polymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB forms a dark brown precipitate.
Reagents provided:
6 ml HRP-Polymer anti-Rabbit (Ready-to-use) Substrate systems recommended: Permanent AEC kit, AEC Single Solution, AEC Substrate kit, DAB Substrate kit, DAB High contrast kit Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out.
Procedure:
1. Peroxide blocking (3 % H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 5 min. 7. HRP-polymer anti-Rabbit 30 min. 8. Washing with wash buffer 3 x 2 min. 9. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 10. Stopping the reaction with distilled H2O when the desired colour intensity is attained 11. Counterstaining and blueing 12. Mounting: aqueous with AEC, permanent with DAB or Permanent AEC
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from rabbit, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use a Blocking Solution or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase in the tissue. Maybe the hydrogen peroxide solution used for blocking was inactivated
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity may cause non-specific staining. The enzyme activity is blocked by incubation with hydrogen peroxide solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagent. In case of the reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining might appear. ProClin is used for stabilisation. A Material safety data sheet (MSDS) is available upon request.
DAB Substrate kit High Contrast is developed for immunohistochemical and in situ-hybridisation staining procedures with horse radish peroxidase (HRP). DAB (3,3-Diaminobenzidine) leads to the formation of a brown precipitate at the location of the target antigen or target nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light microscopy. The kit is especially useful when a high contrast between chromogen and counter stain is desired. Compared to standard DAB staining systems the DAB Substrate High Contrast kit gives a darker brown colour and a higher sensitivity.
3 ml DAB Chromogen (liquid DAB concentrate) 11 x 5 ml DAB Substrate Buffer High Contrast
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. Do not use product after the expiry date. The working solution should be prepared freshly at the day of use. Once the two reagents are combined, the resulting solution is stable for up to six hours. Excess working solution should be disposed as hazardous substance. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
Add 5 drops of DAB Chromogen (DAB concentrate) to one bottle of DAB Substrate Buffer High Contrast and mix thoroughly.
Procedure:
1) Rinse the slide with wash buffer after the previous incubation step. 2) Apply the DAB High contrast working solution to the slide. Incubate for 5-15 minutes. 3) Rinse with distilled H2O. 4) Counterstain with haematoxylin for about 30 seconds up to 5 minutes (depending on the desired staining intensity). 5) Rinse with distilled H2O. 6) Blueing in tap water for at least 5 minutes. 7) Dehydrate through a graded series of ethanol and clear in xylene. Mount with a permanent mounting medium. Note: It is also possible to mount DAB High Contrast with aqueous mounting media.
Expected results:
During the reaction of the substrate with horse radish peroxidase in presence of the chromogen DAB, a brown precipitate is formed at the location of the target antigen or nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light microscopy.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). In some tissues endogenous peroxidase activity may cause non-specific staining. The enzyme activity should be blocked by incubation with hydrogen peroxide solution (H2O2 solution). The step is carried out before incubation with primary antibody but after dewaxing and rehydration. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. The DAB chromogen is hazardous to your health. Wear protective clothing to avoid contact of reagents or specimen with eye, skin or mucous membrane. In case of a reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining may occur. Material safety data sheets (MSDS) are available upon request.
For in-vitro Diagnostic Use. The BrightVision one step detection system Goat Anti-Mouse IgG HRP and Goat anti-rabbit IgG AP, is intended for use in immunohistochemistry for the detection of mouse or rabbit antibodies.
The BrightVision detection system, peroxidase Goat Anti-Mouse HRP/Goat anti-Rabbit AP, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision detection system detects Rabbit and Mouse bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen. The clinical interpretation of any staining or its absence should be determined by a qualified pathologist and complemented by morphologic studies; controls should be evaluated within the context of the patients clinical history and/or other diagnostic tests.
Principle of method:
BrightVision, one step detection system Goat Anti- Mouse HRP and Rabbit AP (Ready-to-Use).
Reagents provided:
BrightVision, One step detection system Goat anti-Mouse HRP / Goat anti-Rabbit AP (Ready-to-use; 55 ml)
Storage and handling:
2-8°C and in the dark
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary mouse and/or rabbit antibody (Antibody; 30 min), 8. Wash buffer (PBS or TBS buffer; 2x 5 min), 9 Detection system, polymer Mouse HRP/Rabbit AP, (Labeled polymer; 30 min), 10. Wash buffer (TBS buffer; 2x 5 min), 11. Substrate (DAB; see applicble IFU), 12. Wash aqua dest (Wash; 2x 2 min), 13. Substrate (Fast Red / New Fuchsin; see applicable IFU), 14. Wash aqua dest (Wash; 2x 2 min), 15. Counterstain and coverslip with aqueous mounting medium.
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
Fast Enzyme is a ready-to-use solution developed for enzymatic epitope retrieval on formalin-fixed tissue sections on slides. This procedure (sometimes called PIER, Protease Induced Epitope Retrieval) is primarily used in immunohistochemical staining procedures. Proteolytic pre-treatment is also used in in situ-hybridisation. Fast Enzyme is intended for research use only.
Immunohistochemical staining procedures consist of sequential incubation steps with blocking solutions, antibodies and secondary reagents, enzymes and chromogenic substrates carried out on tissue sections. These tissue sections are mostly prepared out of formalin-fixed paraffin-embedded tissue blocks. Cellular structures are very effectively stabilised by formalin fixation which results in optimal morphological preservation of the sample. On the other hand the formalin fixation leads to strong cross-links between proteins. This means that epitopes of antigens are being masked and often are no longer accessible for primary antibodies. In order to enable primary antibodies to bind to antigens the epitopes have to be recovered. Enzymatic digestion with proteolytic enzymes (PIER) restores structures of the epitopes making them more accessible to specific antibodies. Heat induced epitope retrieval (HIER) in buffer solutions of different compositions and pH-values is another way of recovering epitopes. The primary antibody used determines the appropriate method.
Principle of method:
Fast Enzyme is a ready-to-use enzyme solution for enzymatic epitope retrieval.
Reagents provided:
15 ml Fast Enzyme (Ready-To-Use)
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Reagent preparation:
The solution is ready-to-use.
Procedure:
Fast Enzyme is suitable for enzymatic epitope retrieval carried out after the dewaxing and rehydration of the tissue sections. 1. Cover deparaffinised and rehydrated tissue sections with ready-to-use Fast Enzyme Solution. 2. Incubate for 5 minutes at room temperature. (It was shown that in individual cases a stronger signal can be obtained when the incubation time is elongated. Usually an incubation for 5 min at room temperatur is sufficient.) 3. Rinse carefully (3 x) with wash buffer. 4. Proceed with immunohistological staining as usual.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent and specimen with eye, skin or mucous membranes. In case of reagent or specimen coming into contact with a sensitive area, wash area with large amounts of water. A material safety data sheet (MSDS) is available upon request.
The Plus HRP Kits, Mouse is based on the streptavidin-biotin system. It is designed for qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with monoclonal primary antibodies and sera obtained from mice. The Plus HRP Kit, Mouse can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Kit, Mouse is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and horse radish peroxidase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus HRP Kit, Mouse binds to mouse primary antibodies. Therefore this kit can detect monoclonal primary antibodies and sera obtained from mice.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide Block). Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and the streptavidin-horse radish peroxidase-conjugate (Streptavidin-HRP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-HRP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed via a light microscope. The chromogen used determines the colour. The chromogen AEC (included only in kit MON-APP123) leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB (included only in kit MON-APP124) forms a dark brown precipitate.
Reagents provided:
8 ml Peroxide Block (ready-to-use) 8 ml Blocking Solution Reagent 1 (ready-to-use) 8 ml Biotinylated Secondary Antibody, Mouse Reagent 2 (ready-to-use) 8 ml Streptavidin-HRP-Conjugate Reagent 3 (ready-to-use) 7 x 5 ml AEC Substrate Buffer 3 ml AEC Concentrate (Chromogen) Substrate systems recommended (if not included in the kit): Permanent AEC kit, AEC single solution, AEC substrate kit, DAB substrate kit, DAB high contrast kit. Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. The tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate AEC working solution (with MON-APP123 only): Add 2 drops (100 µl) of AEC Concentrate to one bottle of AEC Substrate Buffer and mix thoroughly. Preparation of the chromogenic substrate DAB working solution (with MON-APP124 only): Add 4 drops (200 µl) of DAB Concentrate to one bottle of DAB Substrate Buffer and mix thoroughly
Procedure:
1. Peroxide Block (3% H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 2 min. 7. Biotinylated Secondary Antibody, Mouse (Reagent 2, yellow) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Streptavidin-HRP-Conjugate (Reagent 3, red) 10-15 min. 10. Washing with wash buffer 3 x 2 min. 11. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 12. Stopping the reaction with distilled H2O when the desired colour intensity is attained 13. Counterstaining and blueing 14. Mounting: aqueous with AEC, permanent with DAB or Permanent AEC
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase. Maybe the hydrogen peroxide solution used for blocking was inactivated. 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with 3% H2O2 solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Background staining due to endogenous biotin can be blocked through an avidinbiotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) are available upon request.
CryoCompound freezing medium is an aqueous based frozen tissue embedding medium designed to support tissue blocks in cryostat sectioning. Formulated to promote rapid freezing, enhanced sectioning and consistent results at a working temperature of -20° C. The ready-to-use Cryocompound is available in different colors: MON-APP900C (Transparant/colorless), MON-APP900B (Blue), MON-APP900Y (Yellow), MON-APP900O (Orange), MON-APP900G (green), MON-APP900R (Red) or Multicolorkit MON-APP900BYGR (Blue, Yellow, Green, Red).
Principle of method:
Freezing medium
Reagents provided:
100 ml Cryocompound, freezing medium (ready-to-use)
Storage and handling:
Store at room temperature
Procedure:
1. Place few drops of CryoCompound (depends on the size of the sample to be embedded) onto the center of the bottom of cryomold. Be careful to select the proper size embedding mold according to the size of the sample to be embedded. 2. Try to avoid the formation of air bubbles. Remove any bubbles inside the CryoCopound. This is important because the air bubbles will create problems when cutting sections. Air bubbles create freeze- thaw-freeze cycle and ice crystal will form inside of it and result in a very bad morphology due to the ice crystal artefact. 3. Let it settle for 15-30 seconds to allow the CryoCompound to completely wet the surface of the tissue. Hardening of the CryoCompound included the sample (it will happen in 0.5-1 minute) before preparing the CryoCompoundsample-block.
For in-vitro Diagnostic Use. The BrightVision one step detection system peroxidase Goat Anti-Mouse/Rabbit IgG HRP, is intended for use in immunohistochemistry for the detection of mouse or rabbit antibodies.
The BrightVision detection system peroxidase Goat Anti- Mouse/Rabbit HRP, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision detection system detects Mouse or Rabbit bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen (not provided). Also available in 110 ml, 500 ml and 1000 ml.
Principle of method:
One step detection system peroxidase goat anti-mouse/rabbit IgG HRP
Reagents provided:
One step detection system Goat anti-Mouse/Rabbit HRP (Ready-to-use; 55 ml)
Storage and handling:
2-8°C and in the dark
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary mouse or rabbit antibody (Antibody; 30 min), 8. Wash buffer (PBS or TBS buffer; 2x 5 min), 9. Detection system, polymer HRP, (Labeled polymer; 30 min), 10. Wash buffer (PBS or TBS buffer; 2x 5 min), 11. Substrate (DAB; see applicable IFU), 12. Wash aqua dest (Wash; 2x 2 min), 13. Counterstain, dehydrate and coverslip (Auxiliary)
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
The blocking solution Peroxide Block is intended for inhibition of endogenous peroxidase activity in tissue sections. It is primarily intended to be used in immunohistochemistry on formalin-fixed paraffin-embedded samples if using a detection system with horse radish peroxidase.
Endogenous peroxidase activity in the tissue can result in unspecific background staining in immunohistochemical staining procedures using horse radish peroxidase (HRP) as detection enzyme. This effect can be eliminated when tissue sections are incubated with Peroxide Block prior to immunohistochemical staining. Hydrogen peroxide in the solution blocks the activity of endogenous peroxidase.
Principle of method:
Peroxide Block is applied onto tissue sections to reduce non-specific staining due to endogenous peroxidase activity in immunohistochemistry. The step is carried out before incubation with primary antibody but after dewaxing and rehydration. If a heat induced epitope retrieval (HIER) or enzymatic digestion is necessary for immunohistochemical detection it is of no importance if the Peroxide Block is used before or after this step. In some cases it has been shown, that blocking of endogenous peroxidase before the epitope retrieval leads to better results.
Reagents provided:
500 ml Peroxide Block (ready-to-use)
Storage and handling:
The solution should be stored at 2-8°C without furt her dilution. Please store the reagent in a dark place and do not freeze it. Avoid exposure to strong light. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Procedure:
1. Apply Peroxide Block for 10 minutes at room temperature. The section should be covered completely. 2. Rinse with wash buffer. 3. Proceed with next steps for immunohistochemical staining as usual starting with protein blocking or the primary antibody.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, contact our technical support. Also refer to the instructions of the detection systems containing Peroxide Block for guidance on general troubleshooting
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific binding. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent or specimen with eye, skin or mucous membrane. In case of the reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. A material safety data sheet (MSDS) is available upon request
The Plus AP Kit, Mouse is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with monoclonal primary antibodies and sera obtained from mice. The Plus AP Kit, Mouse can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Kit, Mouse is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and alkaline phosphatase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus AP Kit, Mouse binds to mouse primary antibodies. Therefore this kit can detect monoclonal primary antibodies and sera obtained from mice.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and the streptavidinalkaline phosphatase-conjugate (Streptavidin-AP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-AP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent Red (included only in kit MON-APP119) leads to a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
8 ml Blocking Solution Reagent 1 (ready-to-use) 8 ml Biotinylated Secondary Antibody, Mouse Reagent 2 (ready-to-use) 8 ml Streptavidin-AP-Conjugate Reagent 3 (ready-to-use) 8 x 5 ml Permanent Red Buffer (Substrate Buffer) 2 ml Permanent Red Concentrate (Chromogen) Substrate systems recommended (if not included in the kit): Permanent AP Red Kit, BCIP/NBT Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate working solution (with MON-APP119 only): Add 2 drops (60 µl) of Permanent Red Concentrate to one bottle of Permanent Red Buffer (Substrate Buffer) and mix. This solution should be used directly after preparation.
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 2 min. 5. Biotinylated Secondary Antibody, Mouse (Reagent 2, yellow) 10-15 min. 6. Washing with wash buffer 3 x 2 min. 7. Streptavidin-AP-Conjugate (Reagent 3, red) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent Red substrate-chromogen solution (with MON-APP119) 5 min. 10. Wash with distilled H2O 1 min. 11. Permanent Red substrate-chromogen solution (with MON-APP119) 5 min. 12. Wash with destilled water 3 x 1 min. 13. Counterstaining and blueing 14. Mounting: aqueous or permanent after dehydration * The incubation times should be adjusted, when using other substrate-chromogen systems.
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support . No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see section Limitations of the Procedure). 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) for the pure substances are available upon request. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear
The Plus HRP Kits, Mouse is based on the streptavidin-biotin system. It is designed for qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with monoclonal primary antibodies and sera obtained from mice. The Plus HRP Kit, Mouse can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Kit, Mouse is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and horse radish peroxidase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus HRP Kit, Mouse binds to mouse primary antibodies. Therefore this kit can detect monoclonal primary antibodies and sera obtained from mice.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide Block). Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and the streptavidin-horse radish peroxidase-conjugate (Streptavidin-HRP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-HRP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed via a light microscope. The chromogen used determines the colour. The chromogen AEC (included only in kit MON-APP123) leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB (included only in kit MON-APP124) forms a dark brown precipitate.
Reagents provided:
4x 15 ml Blocking Solution Reagent 1 (ready-to-use) 4x 15 ml Biotinylated Secondary Antibody, Mouse Reagent 2 (ready-to-use) 4x 15 ml Streptavidin-HRP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit): Permanent AEC kit, AEC single solution, AEC substrate kit, DAB substrate kit, DAB high contrast kit. Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. The tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate AEC working solution (with MON-APP123 only): Add 2 drops (100 µl) of AEC Concentrate to one bottle of AEC Substrate Buffer and mix thoroughly. Preparation of the chromogenic substrate DAB working solution (with MON-APP124 only): Add 4 drops (200 µl) of DAB Concentrate to one bottle of DAB Substrate Buffer and mix thoroughly
Procedure:
1. Peroxide Block (3% H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 2 min. 7. Biotinylated Secondary Antibody, Mouse (Reagent 2, yellow) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Streptavidin-HRP-Conjugate (Reagent 3, red) 10-15 min. 10. Washing with wash buffer 3 x 2 min. 11. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 12. Stopping the reaction with distilled H2O when the desired colour intensity is attained 13. Counterstaining and blueing 14. Mounting: aqueous with AEC, permanent with DAB or Permanent AEC
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase. Maybe the hydrogen peroxide solution used for blocking was inactivated. 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with 3% H2O2 solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Background staining due to endogenous biotin can be blocked through an avidinbiotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) are available upon request.
The Citrate buffer, is designed for use during heat-induced epitope retrieval (HIER) on formalinfixed paraffin-embedded tissue sections prior to antibody application. In immunohistochemistry (IHC), protein cross-links are formed during formalin or other aldehyde fixation. These cross-links mask the antigenic sites in tissue specimens and results in weak or false negative staining in immunohistochemical detection of proteins. The use of this citrate buffer in combination with heat ensures that the antigenicity of proteins modified, thus enhancing staining intensity of antibodies. For the recommended pre-treatment technique, please refer to the individual antibody's instructions for use. This buffer is a 10x concentrate solution and must be diluted 1:10 with deionized water before using. The final readyto-use solution should have a pH of 6.0 ± 0.3. The buffer can be used for a maximum of three runs within five days after dilution. Also available in 250 ml, 500 ml en 1000 ml.
Before use dilute 1:10 with deionized water. The final ready-to-use solution should have a pH of 6.0 ± 0,3,
Procedure:
1. Deparaffinize and rehydrate the tissue slides. 2. Fill the PT Module tank with 150 ml of citrate buffer and 1,350 ml of deionized water, to obtain 1,500 ml of ready-to-use solution (1:10 dilution). 3. Pre-heat the PT Module until temperature reaches 65°C and place the formalin-fixed slides in slide racks into the PT Module tank. 4. Heat the citrate buffer and slides to 98°C and incubate for 20 minutes. 5. Cool slides in the PT Module to 65°C. 6. Remove slides and cool to room temperature for at least 5 minutes in a PBS or TBS based buffer. 7. Continue with staining according to IHC protocol. Note: Alternative heating sources, such as a microwave or a pressure cooker, can be used to replace the PT Module tank. The optimal incubation time for these heating sources should be determined by authorised personnel / researchers.
The Plus HRP Polymer anti-Mouse kit is designed for the qualitative detection of antigens in fixed paraffinembedded tissue sections, in frozen tissue sections, and in cytological samples. It was developed for use in combination with monoclonal primary antibodies and sera obtained from mice. The reagent can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Polymer anti-Mouse kit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer consists of several molecules of secondary antibodies covalently bound to several molecules of horse radish peroxidase (HRP). Visualisation occurs via an enzyme-substrate reaction in the presence of a colorising reagent which permits microscopical analysis. The test system is suitable for the detection of monoclonal primary antibodies and sera obtained from mice. In contrast to other detection techniques, which often use the streptavidin-biotin system the Plus HRP Polymer antiMouse kit avoids the problem of background staining caused by endogenous biotin in the tissue
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (peroxide block). Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the HRPpolymer is minimized by incubation with a protein blocking solution. This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the HRP-polymer is applied and incubated. Any excess of unbound HRP-polymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB forms a dark brown precipitate.
Reagents provided:
6 mL HRP-Polymer anti-Mouse (ready-to-use) Substrate systems recommended: Permanent AEC kit, AEC single solution, AEC substrate kit, DAB substrate kit, DAB High contrast kit. Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date. It should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support .
Reagent preparation:
Reagent should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out.
Procedure:
1. Peroxide blocking (3 % H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 5 min. 7. HRP-polymer anti-Mouse 30 min. 8. Washing with wash buffer 3 x 2 min. 9. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 10. Stopping the reaction with distilled H2O when the desired colour intensity is attained 11. Counterstaining and blueing 12. Mounting: aqueous with AEC, permanent with DAB or Permanent AEC
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support . No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Nonspecific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase in the tissue. Maybe the hydrogen peroxide solution used for blocking was inactivated
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity may cause non-specific staining. The enzyme activity is blocked by incubation with hydrogen peroxide solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution can result in decreasing signal intensity. Sanbio guarantee that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of the reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining might appear. ProClin 950 is used for stabilisation. A Material safety data sheets (MSDS) is available upon request.
The Plus AP Polymer Kit is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. It is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mice and rabbits. The kit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Polymer Kit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer in this kit consists of several molecules of secondary antibodies covalently bound to several molecules of alkaline phosphatase (AP). Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The test system is suitable for the detection of mono- and polyclonal primary antibodies and sera obtained from mice and rabbits. In contrast to other detection techniques, which often use the streptavidin-biotin system the Plus AP Polymer Kit avoids the problem of background staining caused by endogenous biotin in the tissue.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the AP polymer is minimized by incubation with a protein blocking solution (Blocking Solution, provided with this kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the enhancement reagent (PostBlock) is applied and incubated. A second washing is followed by the application of the AP-polymer. Any excess of unbound APpolymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent AP Red leads to the formation of a magentared product of reaction at the place of the target antigen.
Reagents provided:
6 ml Blocking Solution Reagent 1 (ready-to-use) 6 ml PostBlock Reagent 2 (ready-to-use) 6 ml AP-Polymer (Mouse/Rabbit) Reagent 3 (ready-to-use) Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support.
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 5 min. 5. PostBlock (Reagent 2, yellow) 20 min. 6. Washing with wash buffer 3 x 5 min. 7. AP-polymer (Reagent 3, red) 30 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent AP Red 10-20 min. (Controlling the colour intensity via light microscope is recommended.) 10. Stopping the reaction with distilled H2O when the desired colour intensity is attained 11. Counterstaining and blueing 12. Mounting: permanent or aqueous with Permanent AP Red
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse or rabbit, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see section Limitations of the Procedure).
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Therefore, tissues of this origin should be stained with peroxidase detection systems (i.e. POLHRP-125). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the BlockingSolution instead of just draining it away as in other procedures. We will guarantee that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and ProClin 950 used for stabilisation. Material safety data sheets (MSDS) are available upon request.
Permanent AP Red Kit is developed for immunohistochemical and in situ-hybridisation staining procedures with alkaline phosphatase. Permanent AP Red leads to the formation of a magenta-red precipitate at the location of the target antigen or target nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light or fluorescence microscopy.
500 ml Permanent AP Red Buffer 8 ml Permanent AP Red Chromogen 1 Dilution Vial
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. Do not use product after the expiry date. The working solution prepared is stable for about 60 minutes and should therefore be used directly after preparation. Excess working solution should be discarded. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
Reagent preparation (Preparation of the working solution) 1) Pipette 2.5 ml AP Red Buffer into the provided dilution vial and let it come to room temperature. The chromogen should still be kept cool. 2) Directly prior to use add 1 drop of Permanent AP Red Chromogen into the buffer. Mix thoroughly. 3) The solution is stable for about 60 minutes. Preparation should be done directly before use. Make sure to pipet the chromogen/substrate mix on the last slide of the staining run within 40 min after mixing. If you want to prepare other quantities of the working solution, please use same ratio AP Red Buffer and Chromogen
Procedure:
1) Rinse the slide with wash buffer after the previous incubation step. 2) Apply freshly prepared Permanent AP Red working solution onto the slide. Incubate for 10 minutes. 3) Rinse with distilled H2O. 4) Counterstain with haematoxylin for about 30 seconds up to 5 minutes (depending on the desired staining intensity). 5) Rinse with distilled H2O. 6) Blueing in tap water for at least 5 minutes. 7) Dehydrate through a graded series of ethanol and clear in xylene. Mount with a permanent mounting medium. Note: It is also possible to mount Permanent AP Red with aqueous mounting media.
Expected results:
During the reaction of the substrate with alkaline phosphatase in presence of the chromogen Permanent AP Red, a magenta-red precipitate is formed at the location of the target antigen or nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light or fluorescence microscopy (Texas Red filter).
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). In some tissues endogenous alkaline phosphatase activity may cause non-specific staining. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Therefore, tissues of this origin should be stained with peroxidase detection systems. A higher sensitivity can be obtained when a second chromogenic substrate step is used (i. e. 2 x 10 min Permanent AP Red). Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. A longer exposure to absolute ethanol can result in decreasing staining intensity. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagents or specimen with eye, skin or mucous membrane. In case of a reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. A material safety data sheet (MSDS) is available upon request.
For in-vitro Diagnostic Use. The BrightVision one step detection system Goat Anti-Rabbit IgG HRP and Goat anti-Mouse IgG AP, is intended for use in immunohistochemistry for the detection of mouse or rabbit antibodies.
The BrightVision detection system, peroxidase Goat Anti-Rabbit HRP and Goat anti-Mouse AP, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision detection system detects Rabbit and Mouse bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen. The clinical interpretation of any staining or its absence should be determined by a qualified pathologist and complemented by morphologic studies; controls should be evaluated within the context of the patients clinical history and/or other diagnostic tests.
Principle of method:
BrightVision, one step detection system Goat Anti- Rabbit HRP and Mouse AP (Ready-to-Use).
Reagents provided:
BrightVision, One step detection system Goat anti-Rabbit HRP / Goat anti-Mouse AP (Ready-to-use; 55 ml)
Storage and handling:
2-8°C and in the dark
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary mouse and/or rabbit antibody (Antibody; 30 min), 8. Wash buffer (PBS or TBS buffer; 2x 5 min), 9 Detection system, polymer Rabbit HRP/Mouse AP, (Labeled polymer; 30 min), 10. Wash buffer (TBS buffer; 2x 5 min), 11. Substrate (DAB; see applicble IFU), 12. Wash aqua dest (Wash; 2x 2 min), 13. Substrate (Fast Red / New Fuchsin; see applicable IFU), 14. Wash aqua dest (Wash; 2x 2 min), 15. Counterstain and coverslip with aqueous mounting medium.
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
HIER T-EDTA Buffer pH 9.0 is a solution developed for heat induced epitope retrieval (HIER) in formalin-fixed paraffinembedded tissue sections on slides. This procedure is primarily used in immunohistochemistry.
Immunohistochemical staining procedures consists of sequential incubation steps with blocking solutions, antibodies and secondary reagents, enzymes and chromogenic substrates carried out on tissue sections. These tissue sections are mostly prepared out of formalin-fixed paraffin-embedded tissue blocks. Cellular structures are very effectively stabilised by formalin fixation which results in optimal morphological preservation of the sample. On the other hand the formalin fixation leads to strong cross-links between proteins. This means that epitopes of antigens are being masked and often are no longer accessible for primary antibodies. In order to enable primary antibodies to bind to antigens the epitopes have to be recovered. Heat induced epitope retrieval (HIER) in buffer solutions of different compositions and pH-values restore structures of the epitopes making them more accessible to specific antibodies. Enzymatic digestion with proteolytic enzymes is another way of recovering epitopes. The primary antibody used determines the appropriate method.
Principle of method:
HIER T-EDTA Buffer pH 9.0 is a 10fold concentrated EDTA solution in Tris buffer with additives of detergent and stabilising substances. For preparation of the working strength solution the buffer concentrate is diluted 1:10 with deionised or distilled water. The resulting solution has a pH of 9.0 (8.8 to 9.2). HIER T-EDTA Buffer pH 9.0 is a very efficient epitope retrieval solution in immunohistochemical staining procedures to be used with primary antibodies of many different specificities. It leads to considerably stronger signals compared with usually used citrate buffer.
Reagents provided:
100 ml HIER T-EDTA Buffer pH 9.0 (10fold concentrated, adequate for 1 litre ready-to-use T-EDTA Buffer)
Storage and handling:
The solution should be stored at 2-8°C. Do not free ze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. If stored at room temperature the solution is stable for at least 10 month from the date of delivery. The prepared working strength solution is stable for 1 month, if stored at 2-8°C. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Reagent preparation:
Preparation of the T-EDTA buffer working strength solution: Dilute HIER T-EDTA Buffer concentrate 1:10 with deionised or distilled water and mix thoroughly. The pH-value should be at 9.0 (8.8 to 9.2). If necessary adjust pH-value with diluted NaOH or HCl solution.
Procedure:
HIER T-EDTA Buffer is suitable for various HIER-methods such as steamer, pressure cooker, autoclave, water bath, and microwave oven. Tissue sections used in heat induced epitope retrieval should always be placed on adhesive slides. Epitope retrieval is carried out after dewaxing and rehydration of the sections. Exemplary protocol using steamer: 1. Prepare the working strength solution by diluting the buffer concentrate as described above and transfer to a Coplin jar. Please make sure that there is enough volume to cover the tissue sections on the slides completely. 2. Fill steamer with water according to instruction manual, close lid and start. 3. After 10 minutes place Coplin jar with T-EDTA buffer in the steamer, close the lid and heat the solution for 20 minutes. 4. Place slides with tissue sections into the preheated solution and close the lid. Tissue sections have to be completely covered with T-EDTA buffer solution. 5. Incubate slides 20 40 minutes. The optimal incubation time needs to be elaborated by the operator. 6. After the incubation take the Coplin jar with slides out of steamer and let cool down at room temperature for about 20 minutes. 7. Remove T-EDTA buffer, rinse slides with wash buffer and proceed with immunohistological staining.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific binding. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent and specimen with eye, skin or mucous membranes. In case of reagent or specimen coming into contact with a sensitive area, wash area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. ProClin 300 is used for stabilisation. A material safety data sheet (MSDS) is available upon request.
The Plus AP Kit, Rabbit is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from rabbit. The Plus AP Kit, Rabbit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Kit, Rabbit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and alkaline phosphatase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus AP Kit, Rabbit binds to rabbit primary antibodies. Therefore this kit can detect mono- and polyclonal primary antibodies and sera obtained from rabbit.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This antibody functions as a link between primary antibody and streptavidin-alkaline phosphatase-conjugate (Streptavidin-AP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-AP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent Red (included only in kit MON-APP128) leads to the formation of a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
4x 15 ml Blocking Solution Reagent 1 (ready-to-use) 4x 15 ml Biotinylated Secondary Antibody, Rabbit Reagent 2 (ready-to-use) 4x 15 ml Streptavidin-AP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit) Permanent AP Red kit, BCIP/NBT Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate working solution (with MON-APP128 only): Add 2 drops (60 µl) of Permanent Red Concentrate to one bottle of Permanent Red Buffer (Substrate Buffer) and mix. This solution should be used directly after preparation.
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 2 min. 5. Biotinylated Secondary Antibody, Rabbit (Reagent 2, yellow) 10-15 min. 6. Washing with wash buffer 3 x 2 min. 7. Streptavidin-AP-Conjugate (Reagent 3, red) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent Red substrate-chromogen solution (with AP008RED-RB) 5 min. 10. Wash with distilled H2O 1 min. 11. Permanent Red substrate-chromogen solution (with AP008RED-RB) 5 min. 12. Wash with destilled water 3 x 1 min. 13. Counterstaining and blueing 14. Mounting: aqueous or permanent after dehydration * The incubation times should be adjusted, when using other substrate-chromogen systems
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from rabbit, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see section Limitations of the Procedure). 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific binding.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) for the pure substances are available upon request. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear.
The blocking solution Peroxide Block is intended for inhibition of endogenous peroxidase activity in tissue sections. It is primarily intended to be used in immunohistochemistry on formalin-fixed paraffin-embedded samples if using a detection system with horse radish peroxidase.
Endogenous peroxidase activity in the tissue can result in unspecific background staining in immunohistochemical staining procedures using horse radish peroxidase (HRP) as detection enzyme. This effect can be eliminated when tissue sections are incubated with Peroxide Block prior to immunohistochemical staining. Hydrogen peroxide in the solution blocks the activity of endogenous peroxidase.
Principle of method:
Peroxide Block is applied onto tissue sections to reduce non-specific staining due to endogenous peroxidase activity in immunohistochemistry. The step is carried out before incubation with primary antibody but after dewaxing and rehydration. If a heat induced epitope retrieval (HIER) or enzymatic digestion is necessary for immunohistochemical detection it is of no importance if the Peroxide Block is used before or after this step. In some cases it has been shown, that blocking of endogenous peroxidase before the epitope retrieval leads to better results.
Reagents provided:
100 ml Peroxide Block (ready-to-use)
Storage and handling:
The solution should be stored at 2-8°C without furt her dilution. Please store the reagent in a dark place and do not freeze it. Avoid exposure to strong light. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Procedure:
1. Apply Peroxide Block for 10 minutes at room temperature. The section should be covered completely. 2. Rinse with wash buffer. 3. Proceed with next steps for immunohistochemical staining as usual starting with protein blocking or the primary antibody.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, contact our technical support. Also refer to the instructions of the detection systems containing Peroxide Block for guidance on general troubleshooting
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific binding. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent or specimen with eye, skin or mucous membrane. In case of the reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. A material safety data sheet (MSDS) is available upon request
For in-vitro Diagnostic Use. The BrightVision two components detection system peroxidase Goat Anti-Mouse/Rabbit IgG HRP, is intended for use in immunohistochemistry for the detection of mouse or rabbit antibodies.
The BrightVision detection system peroxidase Goat Anti- Mouse/Rabbit HRP, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision detection system detects Mouse or Rabbit bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen (not provided).
Principle of method:
Two steps detection system goat anti-mouse/rabbit HRP
Reagents provided:
Post-blocking (ready-to-use) (Gold) 55 ml and Polymer Goat Anti-Mouse/Rabbit HRP (ready-to-use) (Ruby) 55 ml.
Storage and handling:
2-8°C and in the dark
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary mouse or rabbit antibody (Antibody; 30 min), 8. Wash buffer (PBS or TBS buffer; 2x 5 min), 9. Detection system, step 1, post-blocking (Post-blocking; 15 min), 10. Wash buffer (PBS or TBS buffer; 2x 5 min), 11. Detection system, step 2, polymer Mouse/Rabbit HRP (Labeled polymer; 30 min), 12. Wash buffer (PBS or TBS buffer; 2x 5 min), 13. If applicable Substrate (DAB), 14. Wash aqua dest (Wash; 2x 2 min), 15. Counterstain, dehydrate and coverslip (Auxiliary)
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
HIER T-EDTA Buffer pH 9.0 is a solution developed for heat induced epitope retrieval (HIER) in formalin-fixed paraffinembedded tissue sections on slides. This procedure is primarily used in immunohistochemistry.
Immunohistochemical staining procedures consists of sequential incubation steps with blocking solutions, antibodies and secondary reagents, enzymes and chromogenic substrates carried out on tissue sections. These tissue sections are mostly prepared out of formalin-fixed paraffin-embedded tissue blocks. Cellular structures are very effectively stabilised by formalin fixation which results in optimal morphological preservation of the sample. On the other hand the formalin fixation leads to strong cross-links between proteins. This means that epitopes of antigens are being masked and often are no longer accessible for primary antibodies. In order to enable primary antibodies to bind to antigens the epitopes have to be recovered. Heat induced epitope retrieval (HIER) in buffer solutions of different compositions and pH-values restore structures of the epitopes making them more accessible to specific antibodies. Enzymatic digestion with proteolytic enzymes is another way of recovering epitopes. The primary antibody used determines the appropriate method.
Principle of method:
HIER T-EDTA Buffer pH 9.0 is a 10fold concentrated EDTA solution in Tris buffer with additives of detergent and stabilising substances. For preparation of the working strength solution the buffer concentrate is diluted 1:10 with deionised or distilled water. The resulting solution has a pH of 9.0 (8.8 to 9.2). HIER T-EDTA Buffer pH 9.0 is a very efficient epitope retrieval solution in immunohistochemical staining procedures to be used with primary antibodies of many different specificities. It leads to considerably stronger signals compared with usually used citrate buffer.
Reagents provided:
500 ml HIER T-EDTA Buffer pH 9.0 (10fold concentrated, adequate for 5 litres ready-to-use T-EDTA Buffer)
Storage and handling:
The solution should be stored at 2-8°C. Do not free ze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. If stored at room temperature the solution is stable for at least 10 month from the date of delivery. The prepared working strength solution is stable for 1 month, if stored at 2-8°C. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Reagent preparation:
Preparation of the T-EDTA buffer working strength solution: Dilute HIER T-EDTA Buffer concentrate 1:10 with deionised or distilled water and mix thoroughly. The pH-value should be at 9.0 (8.8 to 9.2). If necessary adjust pH-value with diluted NaOH or HCl solution.
Procedure:
HIER T-EDTA Buffer is suitable for various HIER-methods such as steamer, pressure cooker, autoclave, water bath, and microwave oven. Tissue sections used in heat induced epitope retrieval should always be placed on adhesive slides. Epitope retrieval is carried out after dewaxing and rehydration of the sections. Exemplary protocol using steamer: 1. Prepare the working strength solution by diluting the buffer concentrate as described above and transfer to a Coplin jar. Please make sure that there is enough volume to cover the tissue sections on the slides completely. 2. Fill steamer with water according to instruction manual, close lid and start. 3. After 10 minutes place Coplin jar with T-EDTA buffer in the steamer, close the lid and heat the solution for 20 minutes. 4. Place slides with tissue sections into the preheated solution and close the lid. Tissue sections have to be completely covered with T-EDTA buffer solution. 5. Incubate slides 20 40 minutes. The optimal incubation time needs to be elaborated by the operator. 6. After the incubation take the Coplin jar with slides out of steamer and let cool down at room temperature for about 20 minutes. 7. Remove T-EDTA buffer, rinse slides with wash buffer and proceed with immunohistological staining.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific binding. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent and specimen with eye, skin or mucous membranes. In case of reagent or specimen coming into contact with a sensitive area, wash area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. ProClin 300 is used for stabilisation. A material safety data sheet (MSDS) is available upon request.
The Plus HRP One-Step Polymer anti-Mouse/Rabbit is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. It was developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mice or rabbit. The kit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP One-Step Polymer anti-Mouse/Rabbit is a highly sensitive detection reagent intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer consists of several molecules of secondary antibodies covalently bound to several molecules of horseradish peroxidase (HRP). Visualisation occurs via an enzyme-substrate reaction in the presence of a colorising reagent which permits microscopical analysis. The test system is suitable for the detection of mono- and polyclonal primary antibodies and sera obtained from mice or rabbit. In contrast to other detection techniques, which often use the streptavidin-biotin system the Plus HRP One-Step Polymer kits avoid the problem of background staining caused by endogenous biotin in the tissue.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (peroxide block). Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the HRP One-Step Polymer is minimized by incubation with a protein blocking solution. This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the HRP One-Step Polymer is applied and incubated. Any excess of unbound polymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB forms a dark brown precipitate.
Reagents provided:
100 mL HRP One-Step-Polymer anti-Mouse/Rabbit (ready-to-use) Substrate systems recommended: Permanent AEC kit, AEC single solution, AEC substrate kit, DAB substrate kit, DAB High contrast kit. Materials required but not supplied: Positive and negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date. It should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support .
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out.
Procedure:
1. Peroxide blocking (3 % H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 5 min. 7. HRP One-Step Polymer anti-Mouse/Rabbit 30 min. 8. Washing with wash buffer 3 x 2 min. 9. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 10. Stopping the reaction with distilled H2O when the desired colour intensity is attained 11. Counterstaining and blueing 12. Mounting: aqueous with AEC, permanent with DAB
Expected results:
During the reaction of the substrate with horseradish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse or rabbit but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Nonspecific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use Blocking Solution or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase in the tissue. Maybe the hydrogen peroxide solution used for blocking was inactivated
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity may cause non-specific staining. The enzyme activity is blocked by incubation with hydrogen peroxide solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horseradish peroxidase) detection systems (Omata et al, 1980). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution can result in decreasing signal intensity. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 950 is used for stabilisation. A Material safety data sheet (MSDS) is available upon request.
The aqua mounting medium is a widely used for coverslipping from aqueous solutions and is non-fluorescing and has an antifade component to increase the viewing time of the specimen. Use Aqua-Poly/Mount with most fluorescent dyes and stains including DAB, Alkaline Phosphatase, Fast Red, AEC (aminoethylcarbazole) and a variety of other chromogens to enhance and retain fluorescent intensity. The mounting medium (water based) can be used for frozen sections, fat stains, chromogens for immunohistochemistry and in situ hybridization as well as other applications requiring a water-soluble mounting medium.
Principle of method:
Coverslipping from aqueous solutions
Reagents provided:
50 ml Mounting medium (water based), ready-to-use.
Storage and handling:
Store at room temperature
Procedure:
1. Prepare slides as required. 2. Prior to coverslipping rinse the slides in distilled or deionized water. 3. Place the bottle upside down with the end cap attached in a container before use. This will help clear of tiny bubbles. 4. Blot excess water from the slide without drying the tissue specimen. The tissue must be moist prior to mounting. 5. Apply enough drops of aqua mounting medium on the tissue section so that the tissue is completely covered. 6. Carefully lower the coverslip at an angle while gently applying pressure to force any excess medium and air bubbles away from the tissue and out from under the coverslip. 7. Slides can be dried at room temperature or at 4°C or in an oven but the temperature hight is depending what type of staining is used. 8. Allow the aqua mounting medium to dry before examine under the microscope.
Antibody Diluent is developed for dilution of primary antibodies. Antibodies diluted with Antibody Diluent are primarily used in immunohistochemistry with formalin-fixed paraffin-embedded tissue sections, but also with frozen, HOPE-fixed, and cytological samples as well as in immunoblot procedures.
Antibody diluents used in immunohistochemistry should protect the antibody from microbial contamination and stabilize the antibody chemically. Antibody Diluent reduces non-specific binding of antibodies to tissue sections and is therefore extremely useful in receiving background-free staining results.
Principle of method:
Immunohistochemical staining procedures often start with incubation of a blocking solution to reduce unspecific binding of primary antibody to tissue sections. This step can be omitted if the antibody used is diluted in Antibody Diluent. Antibody Diluent ? minimises unspecific binding of the primary antibody to the tissue section, ? reduces surface tension of the antibody solution and improves spreading the reagent on the slide, ? increases microbial and chemical stability of the antibody, ? reduces adhesion of antibody to the surface of the vial, ? and minimises the danger of antibody degradation by proteolytic enzymes.
Reagents provided:
100 ml Antibody Diluent (ready-to-use)
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. If stored at room temperature the solution is stable for at least 10 month from the date of delivery. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, contact our technical support. Also refer to the instructions of the detection systems containing Peroxide Block for guidance on general troubleshooting
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use through qualified personnel only. Wear protective clothing to avoid contact of reagents and specimens with eye, skin and mucous membranes. If reagents or specimens come in contact with sensitive area, wash with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. ProClin300 and sodium azide (NaN3) are used for stabilisation. Reaction of sodium azide with lead or copper in drainage pipes can result in the formation of highly explosive metallic azides. Discard the antibody solution in a large volume of running water to avoid formation of deposits. A material safety data sheet (MSDS) for the pure substances is available upon request.
The Plus HRP Kit, Rabbit is based on the streptavidin-biotin system. It is designed for qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from rabbit. The Plus HRP Kit, Rabbit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Kit, Rabbit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and horse radish peroxidase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus HRP Kit, Rabbit binds to rabbit primary antibodies. Therefore this kit can detect mono- and polyclonal primary antibodies and sera obtained from rabbit.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide Block). Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This antibody functions as a link between primary antibody and the streptavidin-horse radish peroxidase-conjugate (Streptavidin-HRP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-HRPconjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC (included only in kit MON-APP132) leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB (included only in kit MON-APP133) forms a dark brown precipitate.
Reagents provided:
8 ml Peroxide Block (ready-to-use) 8 ml Blocking Solution Reagent 1 (ready-to-use) 8 ml Biotinylated Secondary Antibody, Rabbit Reagent 2 (ready-to-use) 8 ml Streptavidin-HRP-Conjugate Reagent 3 (ready-to-use) 7 x 5 ml AEC Substrate Buffer 3 ml AEC Concentrate (Chromogen) Substrate systems recommended (if not included in the kit): Permanent AEC kit, AEC Single Solution, AEC substrate kit, DAB Substrate kit, DAB High Contrast kit Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Procedure:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. The tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate AEC working solution (with MON-APP132 only): Add 2 drops (100 µl) of AEC Concentrate to one bottle of AEC Substrate Buffer and mix thoroughly. Preparation of the chromogenic substrate DAB working solution (with MON-APP133 only): Add 4 drops (200 µl) of DAB Concentrate to one bottle of DAB Substrate Buffer and mix thoroughly.
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from rabbit. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase. Maybe the hydrogen peroxide solution used for blocking was inactivated. 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with 3% H2O2 solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Background staining due to endogenous biotin can be blocked through an avidinbiotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) are available upon request.
The BrightDiluents universal IHC diluent is specially formulated to stabilize antibodies and eliminate backgrounds encountered in immunohistochemistry staining procedures. The diluent contains complex proteins and non-protein mixtures which eliminate histostaining background by blocking Fc receptors and prevents non-specific protein-protein interactions. It can also be used as blocking applied before primary antibodies. If primary antibodies are diluted in this diluent, a blocking step before primary antibodies can generally be omitted. The blocking /diluent solution is supplied in Ready-to-Use format. It should not be diluted to be effective. The diluent contains no azide, therefore, it can be used to dilute and stabilize HRP-conjugates as well as any other solution that need and stabilizing carrier protein, such as Blocking and Poly-AP conjugates. This product should be interpreted by a qualified pathologist with relevant clinical information, morphological and histological studies and with proper controls. The ready-to-use antibody diluent is available in different colors: MON-APP917 (Transparant/colorless), MON-APP917B (Blue), MON-APP917Y (Yellow), MON-APP917G (green), MON-APP917R (Red)
Principle of method:
Antibody diluent
Reagents provided:
125 ml BrightDiluent, normal antibody diluent (ready-to-use)
Pronase Solution is a ready-to-use solution developed for enzymatic epitope retrieval on formalin-fixed tissue sections on slides. This procedure (sometimes called PIER, Protease Induced Epitope Retrieval) is primarily used in immunohistochemical staining procedures. Proteolytic pre-treatments are also used in protocols for in situhybridization. Pronase solution is intended for research use only.
Immunohistochemical staining procedures consist of sequential incubation steps with blocking solutions, antibodies and secondary reagents, enzymes and chromogenic substrates carried out on tissue sections. These tissue sections are mostly prepared out of formalin-fixed paraffin-embedded tissue blocks. Cellular structures are very effectively stabilised by formalin fixation which results in optimal morphological preservation of the sample. On the other hand the formalin fixation leads to strong cross-links between proteins. This means that epitopes of antigens are being masked and often are no longer accessible for primary antibodies. In order to enable primary antibodies to bind to antigens the epitopes have to be recovered. Enzymatic digestion with proteolytic enzymes (PIER) restores structures of the epitopes making them more accessible to specific antibodies. Heat induced epitope retrieval (HIER) in buffer solutions of different compositions and pH-values is another way of recovering epitopes. The primary antibody used determines the appropriate method.
Principle of method:
Pronase Solution is a ready-to-use solution for enzymatic epitope retrieval.
Reagents provided:
250 ml Pronase Solution (Ready-To-Use)
Storage and handling:
The solution should be stored in aliquots at -20°C without further dilution. The solution should be aliquoted in order to avoid repeated freeze and thawing. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date.
Reagent preparation:
Pronase solution is ready-to-use and should be at room temperature prior to use.
Procedure:
Pronase Solution is suitable for enzymatic epitope retrieval carried out after the dewaxing and rehydration of the tissue sections. 1. Cover deparaffinised and rehydrated tissue sections with ready-to-use Pronase Solution. 2. Incubate for 15 - 20 minutes at room temperature. The optimal incubation time needs to be elaborated by the operator. 3. Rinse carefully (3 x), first with distilled water followed by buffer. 4. Proceed with immunohistological staining as usual.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, contact our technical support
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of the reagent with eye, skin or mucous membrane. In case of reagent coming into contact with a sensitive area, wash the area with large amounts of water. Material safety data sheets (MSDS) are available upon request.
The Plus HRP Kit, Rabbit is based on the streptavidin-biotin system. It is designed for qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from rabbit. The Plus HRP Kit, Rabbit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Kit, Rabbit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and horse radish peroxidase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus HRP Kit, Rabbit binds to rabbit primary antibodies. Therefore this kit can detect mono- and polyclonal primary antibodies and sera obtained from rabbit.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide Block). Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This antibody functions as a link between primary antibody and the streptavidin-horse radish peroxidase-conjugate (Streptavidin-HRP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-HRPconjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC (included only in kit MON-APP132) leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB (included only in kit MON-APP133) forms a dark brown precipitate.
Reagents provided:
500 ml Blocking Solution Reagent 1 (ready-to-use) 500 ml Biotinylated Secondary Antibody, Rabbit Reagent 2 (ready-to-use) 500 ml Streptavidin-HRP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit): Permanent AEC kit, AEC Single Solution, AEC substrate kit, DAB Substrate kit, DAB High Contrast kit Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Procedure:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. The tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate AEC working solution (with MON-APP132 only): Add 2 drops (100 µl) of AEC Concentrate to one bottle of AEC Substrate Buffer and mix thoroughly. Preparation of the chromogenic substrate DAB working solution (with MON-APP133 only): Add 4 drops (200 µl) of DAB Concentrate to one bottle of DAB Substrate Buffer and mix thoroughly.
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from rabbit. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase. Maybe the hydrogen peroxide solution used for blocking was inactivated. 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with 3% H2O2 solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Background staining due to endogenous biotin can be blocked through an avidinbiotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) are available upon request.
The Plus AP Kit, Broad Spectrum is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mouse, rabbit, rat, and guinea pig. The Plus AP Kit, Broad Spectrum can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Kits, Broad Spectrum is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and alkaline phosphatase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus AP Kit, Broad Spectrum is polyvalent. With this kit it is therefore possible to detect mono- and polyclonal primary antibodies and sera obtained from mouse, rabbit, rat, and guinea pig.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary or secondary antibody is minimized via incubation with a protein blocking solution (Blocking Solution provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and streptavidin-alkaline phosphatase-conjugate (Streptavidin-AP-Conjugate). A second washing is followed by the application of this conjugate. It binds to biotin at the secondary antibody. Any excess of unbound streptavidin-AP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent Red (included only in kit MON-APP110) leads to the formation of a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
500 ml Blocking Solution Reagent 1 (ready-to-use) 500 ml Biotinylated Secondary Antibody, polyvalent Reagent 2 (ready-to-use) 500 ml Streptavidin-AP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit): Permanent AP Red Kit, BCIP/NBT Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date. It should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support .
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion.Tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate working solution (with MON-APP110 only): Add 2 drops (60 µl) of Permanent Red Concentrate to one bottle of Permanent Red Buffer (substrate buffer) and mix. This solution should be used directly after preparation.
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 2 min. 5. Biotinylated Secondary Antibody, polyvalent (Reagent 2, yellow) 10-15 min. 6. Washing with wash buffer 3 x 2 min. 7. Streptavidin-AP-Conjugate (Reagent 3, red) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent Red substrate-chromogen solution (with MON-APP110) 5 min. 10. Wash with distilled H2O 1 min. 11. Permanent Red substrate-chromogen solution (with MON-APP110) 5 min. 12. Wash with distilled H2O 3 x 1 min. 13. Counterstaining and blueing 14. Mounting: aqueous or permanent after dehydration * The incubation times should be adjusted, when using other substrate-chromogen systems.
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse, rabbit, rat or guinea pig. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolized by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see also Limitations of the procedure). 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. ProClin 300 and sodium azide (NaN3), used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) for the pure substances are available upon request. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear.
The Plus HRP Kit, Broad Spectrum is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mouse, rabbit, rat, and guinea pig. The Plus HRP Kit, Broad Spectrum can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Kit, Broad Spectrum is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and horse radish peroxidase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus HRP Kit, Broad Spectrum is polyvalent. Therefore this kit can detect mono- and polyclonal primary antibodies and sera obtained from mouse, rabbit, rat, and guinea pig.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide Block). Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and the streptavidin-horse radish peroxidase-conjugate (Streptavidin-HRP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-HRP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC (included only in kit MON-APP114) leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB (included only in kit MON-APP115) forms a dark brown precipitate.
Reagents provided:
8 ml Peroxide Block (ready-to-use) 8 ml Blocking Solution Reagent 1 (ready-to-use) 8 ml Biotinylated Secondary Antibody, polyvalent Reagent 2 (ready-to-use) 8 ml Streptavidin-HRP-Conjugate Reagent 3 (ready-to-use) 7 x 5 ml AEC Substrate Buffer 3 ml AEC Concentrate (Chromogen) Substrate systems recommended (if not included in the kit): Permanent AEC kit, AEC single solution, AEC substrate kit, DAB substrate kit, DAB high contrast kit. Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support.
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. The tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate AEC working solution (with MON-APP114 only): Add 2 drops (100 µl) of AEC Concentrate to one bottle of AEC Substrate Buffer and mix thoroughly. Preparation of the chromogenic substrate DAB working solution (with MON-APP115 only): Add 4 drops (200 µl) of DAB Concentrate to one bottle of DAB Substrate Buffer and mix thoroughly.
Procedure:
1. Peroxide Block (3% H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 2 min. 7. Biotinylated Secondary Antibody, polyvalent (Reagent 2, yellow) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Streptavidin-HRP-Conjugate (Reagent 3, red) 10-15 min. 10. Washing with wash buffer 3 x 2 min. 11. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 12. Stopping the reaction with distilled H2O when the desired colour intensity is attained 13. Counterstaining and blueing 14. Mounting: aqueous with AEC, permanent with DAB or Permanent AEC
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support . No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse, rabbit, rat or guinea pig. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase. Maybe the hydrogen peroxide solution used for blocking was inactivated. 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with 3% H2O2 solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Background staining due to endogenous biotin can be blocked through an avidinbiotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) are available upon request.
The Plus HRP One-Step Polymer anti-Mouse/Rabbit is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. It was developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mice or rabbit. The kit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP One-Step Polymer anti-Mouse/Rabbit is a highly sensitive detection reagent intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer consists of several molecules of secondary antibodies covalently bound to several molecules of horseradish peroxidase (HRP). Visualisation occurs via an enzyme-substrate reaction in the presence of a colorising reagent which permits microscopical analysis. The test system is suitable for the detection of mono- and polyclonal primary antibodies and sera obtained from mice or rabbit. In contrast to other detection techniques, which often use the streptavidin-biotin system the Plus HRP One-Step Polymer kits avoid the problem of background staining caused by endogenous biotin in the tissue.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (peroxide block). Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the HRP One-Step Polymer is minimized by incubation with a protein blocking solution. This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the HRP One-Step Polymer is applied and incubated. Any excess of unbound polymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB forms a dark brown precipitate.
Reagents provided:
6 mL HRP One-Step-Polymer anti-Mouse/Rabbit (ready-to-use) Substrate systems recommended: Permanent AEC kit, AEC single solution, AEC substrate kit, DAB substrate kit, DAB High contrast kit. Materials required but not supplied: Positive and negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date. It should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support .
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out.
Procedure:
1. Peroxide blocking (3 % H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 5 min. 7. HRP One-Step Polymer anti-Mouse/Rabbit 30 min. 8. Washing with wash buffer 3 x 2 min. 9. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 10. Stopping the reaction with distilled H2O when the desired colour intensity is attained 11. Counterstaining and blueing 12. Mounting: aqueous with AEC, permanent with DAB
Expected results:
During the reaction of the substrate with horseradish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse or rabbit but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Nonspecific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use Blocking Solution or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase in the tissue. Maybe the hydrogen peroxide solution used for blocking was inactivated
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity may cause non-specific staining. The enzyme activity is blocked by incubation with hydrogen peroxide solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horseradish peroxidase) detection systems (Omata et al, 1980). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution can result in decreasing signal intensity. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 950 is used for stabilisation. A Material safety data sheet (MSDS) is available upon request.
DAB Substrate kit is intended for immunohistochemical and in situ-hybridisation staining procedures with horse radish peroxidase (HRP). DAB (3,3-Diaminobenzidine) leads to the formation of a brown precipitate at the location of the target antigen or target nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light microscopy.
30 ml DAB Chromogen (liquid DAB concentrate) 500 ml DAB Substrate Buffer
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. Do not use product after the expiry date. The working solution should be prepared freshly at the day of use. Once the two reagents are combined, the resulting solution can be used for up to six hours. Excess working solution needs to be disposed as hazardous substance. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
Add 50 µl DAB Chromogen (DAB concentrate) to 1 ml of DAB Substrate Buffer and mix thoroughly. Note: Typical working concentrations are 50 µl (0.9 mg) DAB per ml substrate buffer. The colour intensity can be adjusted by decreasing or increasing the DAB concentration in the working solution. Maximum sensitivity in immunohistochemical staining can be achieved by working concentrations of about 80 µl (1.5 mg) DAB per ml substrate buffer.
Procedure:
1) Rinse the slide with wash buffer after the previous incubation step. 2) Apply the DAB working solution onto the slide. Incubate for 5-15 minutes. 3) Rinse with distilled H2O. 4) Counterstain with haematoxylin for about 30 seconds up to 5 minutes (depending on the desired staining intensity). 5) Rinse with distilled H2O. 6) Blueing in tap water for at least 5 minutes. 7) Dehydrate through a graded series of ethanol and clear in xylene. Mount with a permanent mounting medium. Note: It is also possible to mount DAB with aqueous mounting media.
Expected results:
During the reaction of the substrate with horse radish peroxidase in presence of the chromogen DAB, a brown precipitate is formed at the location of the target antigen or nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light microscopy.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). In some tissues endogenous peroxidase activity may cause non-specific staining. The enzyme activity should be blocked by incubation with hydrogen peroxide solution (H2O2 solution). The step is carried out before incubation with primary antibody but after dewaxing and rehydration. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. The DAB chromogen is hazardous to your health. Wear protective clothing to avoid contact of reagents or specimen with eye, skin or mucous membrane. In case of a reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining may occur. Material safety data sheets (MSDS) are available upon request.
For in-vitro Diagnostic Use. The BrightVision one step detection system Goat Anti-Mouse/Rabbit IgG AP, is intended for use in immunohistochemistry for the detection of mouse or rabbit antibodies.
The BrightVision detection system Goat Anti- Mouse/Rabbit AP, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision detection system detects Mouse or Rabbit bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen (not provided). Also available in 110 ml, 500 ml and 1000 ml.
Principle of method:
One step detection system goat anti-mouse/rabbit IgG AP
Reagents provided:
One step detection system Goat anti-Mouse/Rabbit AP (Ready-to-use; 55 ml)
Storage and handling:
2-8°C and in the dark
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary mouse or rabbit antibody (Antibody; 30 min), 8. Wash buffer (PBS or TBS buffer; 2x 5 min), 9. Detection system, polymer Mouse/Rabbit AP, (Labeled polymer; 30 min), 10. Wash buffer (TBS buffer; 2x 5 min), 11. Substrate (Fast Red / New Fuchsin, see applicable IFU), 12. Wash aqua dest (Wash; 2x 2 min), 13. Counterstain and coverslip with aqueous mounting medium.
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
For in-vitro Diagnostic Use. The BrightVision two components detection system peroxidase Goat Anti-Mouse/Rabbit IgG HRP, is intended for use in immunohistochemistry for the detection of mouse or rabbit antibodies.
The BrightVision detection system peroxidase Goat Anti- Mouse/Rabbit HRP, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision detection system detects Mouse or Rabbit bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen (not provided).
Principle of method:
Two steps detection system goat anti-mouse/rabbit HRP
Reagents provided:
Post-blocking (ready-to-use) 55 ml and Polymer Goat Anti-Mouse/Rabbit HRP (ready-to-use) 55 ml.
Storage and handling:
2-8°C and in the dark
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary mouse or rabbit antibody (Antibody; 30 min), 8. Wash buffer (PBS or TBS buffer; 2x 5 min), 9. Detection system, step 1, post-blocking (Post-blocking; 15 min), 10. Wash buffer (PBS or TBS buffer; 2x 5 min), 11. Detection system, step 2, polymer Mouse/Rabbit HRP (Labeled polymer; 30 min), 12. Wash buffer (PBS or TBS buffer; 2x 5 min), 13. If applicable Substrate (DAB), 14. Wash aqua dest (Wash; 2x 2 min), 15. Counterstain, dehydrate and coverslip (Auxiliary)
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
The Plus AP Polymer anti-Mouse is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. It is developed for use in combination with monoclonal primary antibodies obtained from mouse. The reagent can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Polymer anti-Mouse is a highly sensitive detection reagent intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer in this kit consists of several molecules of secondary antibodies covalently bound to several molecules of alkaline phosphatase (AP). Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The reagent is suitable for the detection of mono- and polyclonal primary antibodies and sera obtained from mouse. In contrast to other detection techniques, which often use the streptavidin-biotin system the Plus AP Polymer anti-Mouse avoids the problem of background staining caused by endogenous biotin in the tissue.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the AP polymer is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the AP-polymer is applied and incubated. Any excess of unbound AP-polymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Fast Red leads to the formation of a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red), New Fuchsin (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
6 ml AP-Polymer anti-Mouse (Ready-to-use) Substrate systems recommended: Permanent AP Red kit, Fast Red substrate kit, New Fuchsin kit. Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without furt her dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. It should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support.
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out
Procedure:
1. Blocking Solution (protein block, this step is optional) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 5 min. 5. AP-polymer anti Mouse 30 min. 6. Washing with wash buffer 3 x 2 min. 7. Fast Red, Permanent AP Red, NBT/BCIP or New Fuchsin 5-15 min. (Controlling the colour intensity via light microscope is recommended.) 8. Stopping the reaction with distilled H2O when the desired colour intensity is attained 9. Counterstaining and blueing 10. Mounting: aqueous with Fast Red, permanent with Permanent AP Red, NBT/BCIP or New Fuchsin
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use a Blocking Solution or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high).
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of the reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining might appear. ProClin 950 is used for stabilisation. A Material safety data sheet (MSDS) is available upon request.
AEC Single Solution is a ready-to-use solution intended for immunohistochemical and in situ-hybridisation staining procedures with horse radish peroxidase (HRP). AEC (3-Amino-9-ethylcarbazol) leads to the formation of a red-brown precipitate at the location of the target antigen or target nucleic acid. The precipitate is insoluble in aqueous mounting media and can be observed by light microscopy. AEC Single Solution is especially useful when a high sensitivity is desired.
100 ml AEC Single Solution (ready-to-use) 2 Dropper Bottles
Storage and handling:
The solution should be stored at 2-8°C without furt her dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. AEC Single Solution is a ready-to-use solution. Preparation of a working solution as in other chromogenic substrates is not necessary. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
The solution is ready-to-use. AEC Single Solution can be used directly from the refrigerator and should be stored again at 2-8°C aft er use. When using the small package (8 ml) please directly drop from the bottle. When using the 100 ml package (MON-APP209) please transfer up to 8 ml of the AEC Single Solution into one of the provided dropper bottles. The transferred solution is stable for many weeks if stored at 2-8°C. The volume required for several staining runs should be transferred so that the 100 ml stock bottle has to be opened only a few times. If you would like to pipette the solution use a clean vial from which you pipette. Remaining quantities should not be filled back into the bottle but disposed as hazardous material.
Procedure:
1) Rinse the slide with wash buffer after the previous incubation step. 2) Apply the AEC Single Solution to the slide. Incubate for 3-6 minutes. (Incubation time can be extended up to 30 minutes, if desired.) 3) Rinse with distilled H2O. 4) Counterstain with haematoxylin for about 30 seconds up to 5 minutes (depending on the desired staining intensity). 5) Rinse with distilled H2O. 6) Blueing in tap water for at least 5 minutes. 7) Mount with an aqueous mounting medium.
Expected results:
During the reaction of the substrate with horse radish peroxidase in presence of the chromogen AEC, a red-brown precipitate is formed at the location of the target antigen or nucleic acid. The precipitate is insoluble in aqueous solvents and can be observed by light microscopy.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). In some tissues endogenous peroxidase activity may cause non-specific staining. The enzyme activity should be blocked by incubation with hydrogen peroxide solution (H2O2 solution). The step is carried out before incubation with primary antibody but after dewaxing and rehydration. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. The coloured precipitate formed by AEC is soluble in organic solvents. The tissue sections therefore have to be counterstained with aqueous solutions (e. g. Gills or Mayers haematoxylin) and mounted with aqueous mounting media. The colour intensity of the reaction product can decrease with time, especially when exposed to light. The staining reaction itself can be influenced in the same way when carried out in strong light. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. AEC (3-Amino-9-ethylcarbazol) and the solvents used are considered hazardous materials. Material safety data sheets (MSDS) are available upon request. Wear protective clothing to avoid contact of reagent or specimen with eye, skin or mucous membrane. In case of reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Oxidising substances, e. g. metals, dust, bacteria or glass devices can influence the stability of AEC Single Solution. Such contaminations have to be avoided. Non-consumed solution needs to be discarded as dangerous substance.
Aqueous Mount is an aqueous mounting medium for histological and cytological preparations. It is especially suitable for mounting of tissue sections stained with alcohol-soluble chromogenic substrates such as Fast Red or AEC. Even sections stained with alcohol-resistant chromogenic substrates can be mounted with Aqueous Mount if they were not previously dehydrated. Aqueous Mount is intended for research use only.
Aqueous Mount in the following formats: 30 ml Ready-to-use
Storage and handling:
The solution should be stored at room temperature in the original container without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
The solution is ready-to-use
Procedure:
Apply a sufficient amount of Aqueous Mount onto the stained histological or cytological section; depending on the size of section 2 to 5 drops. Cover with a coverslip. Heating of the mounted section for hardening is not necessary. Coverslips can be removed by soaking the section over night in water.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagents or specimen with eye, skin or mucous membrane. In case of a reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. In case of swallowing rinse the mouth excessively with large amounts of water and turn to a doctor. A material safety data sheet (MSDS) is available upon request.
The wash Buffer is designed as washing solution for immunohistochemical and immunocytological staining procedures on slides. Wash Buffer is primarily used with formalin-fixed paraffin-embedded tissue sections, but also with frozen, HOPE-fixed, and cytological samples as well as in immunoblot procedures. The Wash Buffer is suitable for manually operated and automated immunohistochemical staining.
Immunohistochemical staining procedures consist of sequential incubation steps with blocking solutions, antibodies and secondary reagents, enzymes and chromogenic substrates carried out on tissue sections. Washing away the applied reagents after each incubation step is critical to receive optimally stained samples. The Wash Buffer is especially designed for effective washing and therefore ensures brilliant staining results.
Principle of method:
The Wash Buffer is a 20fold concentrated phosphate buffer with additives of sodium chloride, detergent, and stabilising substances. For preparation of the working strength solution the buffer concentrate is diluted 1:20 with deionised or distilled water. The resulting solution has a pH of 7.2 (7.0 to 7.4). The Wash Buffer is wetting the tissue sections with detergent and thus reduces surface tension and improves spreading the reagents on the tissue section, reduces unspecific binding of reagents on the tissue sample, and because of the exact tuned salt concentration effects an excellent preservation of cell morphology.
Reagents provided:
500 ml Wash Buffer (20fold concentrated, adequate for 10 litres ready-to-use wash buffer)
Storage and handling:
The solution should be stored at room temperature. It is stable up to the expiry date indicated on the label if undiluted. Do not use product after the expiry date. The diluted working strength solution is stable for about 1 week depending on the ambient temperature. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Reagent preparation:
Preparation of the Wash Buffer working strength solution: Dilute Wash Buffer concentrate 1:20 with deionised or distilled water and mix thoroughly. The pH-value should be at 7.2 (7.0 to 7.4). If necessary adjust pH-value with diluted NaOH or HCl solution.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. The Wash Buffer is a 20fold concentrated solution with a mildly acidic pH-value. The correct pHvalue of about 7.0 (+/- 0.2) is achieved after diluting the solution 1:20. Sometimes deionised water has pH-values considerably different from the neutral point (pH 7.0) depending on the preparation method. Experiments have shown that the Wash Buffer can successfully be diluted with deionised or distilled with water in the pH-range of 5.5 up to 9.5. If a detection system with alkaline phosphatase is used please note: larger amounts of wash buffer remaining on the slides can lead to decreasing enzyme activity. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent or specimen with eye, skin or mucous membrane. In case of the reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. ProClin 300 is used for stabilisation. A material safety data sheet (MSDS) is available upon request.
The Plus HRP Polymer anti-Rabbit is designed for the qualitative detection of antigens in fixed paraffinembedded tissue sections, in frozen tissue sections, and in cytological samples. It is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from rabbits. The reagent can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Polymer anti-Rabbit is a highly sensitive detection reagent intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer in this kit consists of several molecules of secondary antibodies covalently bound to several molecules of horse radish peroxidase (HRP). Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The reagent is suitable for the detection of mono- and polyclonal primary antibodies and sera obtained from rabbits. In contrast to other detection techniques, which often use the streptavidin-biotin system the Plus HRP Polymer anti-Rabbit avoids the problem of background staining caused by endogenous biotin in the tissue.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide block). Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the HRP polymer is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the HRP-polymer is applied and incubated. Any excess of unbound HRP-polymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB forms a dark brown precipitate.
Reagents provided:
100 ml HRP-Polymer anti-Rabbit (Ready-to-use) Substrate systems recommended: Permanent AEC kit, AEC Single Solution, AEC Substrate kit, DAB Substrate kit, DAB High contrast kit Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out.
Procedure:
1. Peroxide blocking (3 % H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 5 min. 7. HRP-polymer anti-Rabbit 30 min. 8. Washing with wash buffer 3 x 2 min. 9. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 10. Stopping the reaction with distilled H2O when the desired colour intensity is attained 11. Counterstaining and blueing 12. Mounting: aqueous with AEC, permanent with DAB or Permanent AEC
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from rabbit, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use a Blocking Solution or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase in the tissue. Maybe the hydrogen peroxide solution used for blocking was inactivated
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity may cause non-specific staining. The enzyme activity is blocked by incubation with hydrogen peroxide solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagent. In case of the reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining might appear. ProClin is used for stabilisation. A Material safety data sheet (MSDS) is available upon request.
HIER EDTA Buffer pH 8.0 is a solution developed for heat induced epitope retrieval (HIER) in formalin-fixed paraffinembedded tissue sections on slides. This procedure is primarily used in immunohistochemistry.
Immunohistochemical staining procedures consist of sequential incubation steps with blocking solutions, antibodies and secondary reagents, enzymes and chromogenic substrates carried out on tissue sections. These tissue sections are mostly prepared out of formalin-fixed paraffin-embedded tissue blocks. Cellular structures are very effectively stabilised by formalin fixation which results in optimal morphological preservation of the sample. On the other hand the formalin fixation leads to strong cross-links between proteins. This means that epitopes of antigens are being masked and often are no longer accessible for primary antibodies. In order to enable primary antibodies to bind to the antigens the epitopes have to be recovered. Heat induced epitope retrieval (HIER) in buffer solutions of different compositions and pH-values restore structures of the epitopes making them more accessible to specific antibodies. Enzymatic digestion with proteolytic enzymes is another way of recovering epitopes. The primary antibody used determines the appropriate method.
Principle of method:
HIER EDTA Buffer pH 8.0 is a 10fold concentrated, buffered EDTA solution with additives of detergent and stabilising substances. For preparation of the working strength solution the buffer concentrate is diluted 1:10 with deionised or distilled water. The resulting solution has a pH of 8.0 (7.8 to 8.2). HIER EDTA Buffer pH 8.0 is a very efficient epitope retrieval solution in immunohistochemical staining procedures to be used with primary antibodies of different specificity. HIER EDTA Buffer pH 8.0 leads to considerably stronger signals compared with usually used citrate buffer.
Reagents provided:
500 ml HIER EDTA Buffer pH 8.0 (10fold concentrated, adequate for 5 litres ready-to-use EDTA Buffer)
Storage and handling:
The solution should be stored at 2-8°C. Do not free ze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. If stored at room temperature the solution is stable for at least 10 month from the date of delivery. The prepared working strength solution is stable for 1 month, if stored at 2-8°C. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Reagent preparation:
Preparation of the EDTA buffer working strength solution: Dilute HIER EDTA Buffer concentrate 1:10 with deionised or distilled water and mix thoroughly. The pH-value should be at 8.0 (7.8 to 8.2). If necessary adjust pH-value with diluted NaOH or HCl solution.
Procedure:
HIER EDTA Buffer is suitable for various HIER-methods such as steamer, pressure cooker, autoclave, water bath, and microwave oven. Tissue sections used in heat induced epitope retrieval should always be placed on adhesive slides. Epitope retrieval is carried out after dewaxing and rehydration of the sections. Exemplary protocol using steamer: 1. Prepare the working strength solution by diluting the buffer concentrate as described above and transfer to a Coplin jar. Please make sure that there is enough volume to cover the tissue sections on the slides completely. 2. Fill steamer with water according to instruction manual, close lid and start. 3. After 10 minutes place Coplin jar with EDTA buffer in the steamer, close lid and heat the solution for 20 minutes. 4. Place slides with tissue sections into the preheated solution and close the lid. Tissue sections have to be completely covered with EDTA buffer solution. 5. Incubate slides 20 40 minutes. The optimal incubation time needs to be elaborated by the operator. 6. After the incubation take the Coplin jar with slides out of steamer and let cool down at room temperature for about 20 minutes. 7. Remove EDTA buffer, rinse slides with wash buffer and proceed with immunohistological staining.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific binding. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent and specimen with eye, skin or mucous membranes. In case of reagent or specimen coming into contact with a sensitive area, wash area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. ProClin 300 is used for stabilisation. A material safety data sheet (MSDS) is available upon request.
The BrightDiluents universal IHC diluent is specially formulated to stabilize antibodies and eliminate backgrounds encountered in immunohistochemistry staining procedures. The diluent contains complex proteins and non-protein mixtures which eliminate histostaining background by blocking Fc receptors and prevents non-specific protein-protein interactions. It can also be used as blocking applied before primary antibodies. If primary antibodies are diluted in this diluent, a blocking step before primary antibodies can generally be omitted. The blocking /diluent solution is supplied in Ready-to-Use format. It should not be diluted to be effective. The diluent contains no azide, therefore, it can be used to dilute and stabilize HRP-conjugates as well as any other solution that need and stabilizing carrier protein, such as Blocking and Poly-AP conjugates. This product should be interpreted by a qualified pathologist with relevant clinical information, morphological and histological studies and with proper controls. The ready-to-use antibody diluent is available in different colors: MON-APP917 (Transparant/colorless), MON-APP917B (Blue), MON-APP917Y (Yellow), MON-APP917G (green), MON-APP917R (Red)
Principle of method:
Antibody diluent
Reagents provided:
125 ml BrightDiluent, normal antibody diluent (ready-to-use)
CryoCompound freezing medium is an aqueous based frozen tissue embedding medium designed to support tissue blocks in cryostat sectioning. Formulated to promote rapid freezing, enhanced sectioning and consistent results at a working temperature of -20° C. The ready-to-use Cryocompound is available in different colors: MON-APP900C (Transparant/colorless), MON-APP900B (Blue), MON-APP900Y (Yellow), MON-APP900O (Orange), MON-APP900G (green), MON-APP900R (Red) or Multicolorkit MON-APP900BYGR (Blue, Yellow, Green, Red).
Principle of method:
Freezing medium
Reagents provided:
100 ml Cryocompound, freezing medium (ready-to-use)
Storage and handling:
Store at room temperature
Procedure:
1. Place few drops of CryoCompound (depends on the size of the sample to be embedded) onto the center of the bottom of cryomold. Be careful to select the proper size embedding mold according to the size of the sample to be embedded. 2. Try to avoid the formation of air bubbles. Remove any bubbles inside the CryoCopound. This is important because the air bubbles will create problems when cutting sections. Air bubbles create freeze- thaw-freeze cycle and ice crystal will form inside of it and result in a very bad morphology due to the ice crystal artefact. 3. Let it settle for 15-30 seconds to allow the CryoCompound to completely wet the surface of the tissue. Hardening of the CryoCompound included the sample (it will happen in 0.5-1 minute) before preparing the CryoCompoundsample-block.
Aqueous Mount is an aqueous mounting medium for histological and cytological preparations. It is especially suitable for mounting of tissue sections stained with alcohol-soluble chromogenic substrates such as Fast Red or AEC. Even sections stained with alcohol-resistant chromogenic substrates can be mounted with Aqueous Mount if they were not previously dehydrated. Aqueous Mount is intended for research use only.
Aqueous Mount in the following formats: 60 ml Ready-to-use
Storage and handling:
The solution should be stored at room temperature in the original container without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
The solution is ready-to-use
Procedure:
Apply a sufficient amount of Aqueous Mount onto the stained histological or cytological section; depending on the size of section 2 to 5 drops. Cover with a coverslip. Heating of the mounted section for hardening is not necessary. Coverslips can be removed by soaking the section over night in water.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagents or specimen with eye, skin or mucous membrane. In case of a reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. In case of swallowing rinse the mouth excessively with large amounts of water and turn to a doctor. A material safety data sheet (MSDS) is available upon request.
The Plus AP Kit, Mouse is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with monoclonal primary antibodies and sera obtained from mice. The Plus AP Kit, Mouse can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Kit, Mouse is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and alkaline phosphatase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus AP Kit, Mouse binds to mouse primary antibodies. Therefore this kit can detect monoclonal primary antibodies and sera obtained from mice.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and the streptavidinalkaline phosphatase-conjugate (Streptavidin-AP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-AP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent Red (included only in kit MON-APP119) leads to a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
4x 15 ml Blocking Solution Reagent 1 (ready-to-use) 4x 15 ml Biotinylated Secondary Antibody, Mouse Reagent 2 (ready-to-use) 4x 15 ml Streptavidin-AP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit): Permanent AP Red Kit, BCIP/NBT Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate working solution (with MON-APP119 only): Add 2 drops (60 µl) of Permanent Red Concentrate to one bottle of Permanent Red Buffer (Substrate Buffer) and mix. This solution should be used directly after preparation.
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 2 min. 5. Biotinylated Secondary Antibody, Mouse (Reagent 2, yellow) 10-15 min. 6. Washing with wash buffer 3 x 2 min. 7. Streptavidin-AP-Conjugate (Reagent 3, red) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent Red substrate-chromogen solution (with MON-APP119) 5 min. 10. Wash with distilled H2O 1 min. 11. Permanent Red substrate-chromogen solution (with MON-APP119) 5 min. 12. Wash with destilled water 3 x 1 min. 13. Counterstaining and blueing 14. Mounting: aqueous or permanent after dehydration * The incubation times should be adjusted, when using other substrate-chromogen systems.
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support . No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see section Limitations of the Procedure). 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) for the pure substances are available upon request. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear
The Plus AP Polymer anti-Mouse is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. It is developed for use in combination with monoclonal primary antibodies obtained from mouse. The reagent can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Polymer anti-Mouse is a highly sensitive detection reagent intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer in this kit consists of several molecules of secondary antibodies covalently bound to several molecules of alkaline phosphatase (AP). Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The reagent is suitable for the detection of mono- and polyclonal primary antibodies and sera obtained from mouse. In contrast to other detection techniques, which often use the streptavidin-biotin system the Plus AP Polymer anti-Mouse avoids the problem of background staining caused by endogenous biotin in the tissue.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the AP polymer is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the AP-polymer is applied and incubated. Any excess of unbound AP-polymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Fast Red leads to the formation of a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red), New Fuchsin (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
100 ml AP-Polymer anti-Mouse (Ready-to-use) Substrate systems recommended: Permanent AP Red kit, Fast Red substrate kit, New Fuchsin kit. Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without furt her dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. It should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support.
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out
Procedure:
1. Blocking Solution (protein block, this step is optional) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 5 min. 5. AP-polymer anti Mouse 30 min. 6. Washing with wash buffer 3 x 2 min. 7. Fast Red, Permanent AP Red, NBT/BCIP or New Fuchsin 5-15 min. (Controlling the colour intensity via light microscope is recommended.) 8. Stopping the reaction with distilled H2O when the desired colour intensity is attained 9. Counterstaining and blueing 10. Mounting: aqueous with Fast Red, permanent with Permanent AP Red, NBT/BCIP or New Fuchsin
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use a Blocking Solution or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high).
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light.Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of the reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining might appear. ProClin 950 is used for stabilisation. A Material safety data sheet (MSDS) is available upon request.
Permanent HRP Green Kit is intended for immunohistochemical and in situ-hybridisation staining procedures with horse radish peroxidase (HRP). It results in the formation of a green precipitate at the location of the target antigen or target nucleic acid. The precipitate is insoluble in organic solvents and can be observed by light microscopy. The HRP Green precipitate shows a very good contrast to red chromogenic substrates used with alkaline phosphatase detection systems and is therefore especially recommended for double stains. Permanent HRP Green Kit is intended for research use only.
100 ml HRP Green Substrate Buffer 3 ml HRP Green Chromogen 1 Dilution Vial
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. Do not use product after the expiry date. The working solution should be prepared freshly at the day of use. It is stable for at least 4 hours. Excess working solution should be disposed. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
1) Pipette 1 ml HRP Green Substrate Buffer into the provided dilution vial. 2) Add 1 drop (30 µl) of HRP Green Chromogen. Mix thoroughly. 3) The resulting working solution is stable for at least 4 hours. If you want to prepare other quantities of the working solution, please use the same ratio HRP Green Substrate and HRP Chromogen.
Procedure:
1) Rinse the slide with wash buffer after the previous incubation step. 2) Apply the Permanent HRP Green working solution onto the slide. Incubate for 2-10 minutes. 3) Rinse with distilled H2O. 4) Counterstain with haematoxylin for about 30 seconds up to 5 minutes (depending on the desired staining intensity). 5) Rinse with distilled H2O. 6) Blueing in tap water for 5 minutes. 7) Dehydrate through a graded series of ethanol and clear in xylene. Do not exceed incubation times of 30 sec per dehydration step. Use only high purity xylene. Mount with a permanent mounting medium. Note: The colour intensity can be intensified by increasing the chromogen concentration (up to 3 drops or 90 µl chromogen) in the working solution. Lithium carbonate may have a negative effect on the staining result. We recommend to only bluing in tap water. Occasionally precipitates may appear in the HRP Green Chromogen solution. This doesnt affect the staining result.
Expected results:
During the reaction of the substrate with horse radish peroxidase in presence of the Permanent HRP Green chromogen, a green precipitate is formed at the location of the target antigen or nucleic acid. The precipitate is insoluble in organic solvents and can be observed by light microscopy.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Too long incubation steps at the final dehydration serious can diminish the staining intensity. Also low grade xylene and some forms of recycled alcohol can have a negative effect on the staining result. In double stain procedures we recommend to use Permanent HRP Green as the last chromogen. Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagents or specimen with eye, skin or mucous membrane. In case of a reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining may occur. Material safety data sheets (MSDS) are available upon request.
For in-vitro Diagnostic Use. The BrightVision one step detection system peroxidase Goat Anti-Rabbit IgG HRP, is intended for use in immunohistochemistry for the detection of rabbit antibodies.
The BrightVision detection system peroxidase Goat Anti-Rabbit HRP, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision detection system detects Rabbit bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen (not provided). Also available in 110 ml, 500 ml and 1000 ml.
Principle of method:
One step detection system peroxidase goat anti-rabbit IgG HRP
Reagents provided:
One step detection system Goat anti-Rabbit HRP (Ready-to-use; 55 ml)
Storage and handling:
2-8°C and in the dark
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. H2O2 (conc3%) (Tissue preparing; 10 min), 5. Wash buffer (PBS or TBS buffer; 2x 5 min), 6. Primary rabbit antibody (Antibody; 30 min), 7. Wash buffer (PBS or TBS buffer; 2x 5 min), 8. Detection system, polymer Rabbit HRP, (Labeled polymer; 30 min), 9. Wash buffer (PBS or TBS buffer; 2x 5 min), 10. Substrate (DAB; see applicable IFU), 11. Wash aqua dest (Wash; 2x 2 min), 12. Counterstain, dehydrate and coverslip (Auxiliary)
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
For in-vitro Diagnostic Use. The BrightVision one step detection system peroxidase Goat Anti-Mouse IgG AP, is intended for use in immunohistochemistry for the detection of mouse antibodies.
The BrightVision detection system Goat Anti- Mouse AP, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision detection system detects Mouse bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen (not provided). Also available in 110 ml, 500 ml and 1000 ml.
Principle of method:
One step detection system peroxidase goat anti-mouse IgG AP
Reagents provided:
One step detection system Goat anti-Mouse AP (Ready-to-use; 55 ml)
Storage and handling:
2-8°C and in the dark
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary mouse antibody (Antibody; 30 min), 8. Wash buffer (TBS buffer; 2x 5 min), 9. Detection system, polymer Mouse AP, (Labeled polymer; 30 min), 10. Wash buffer (TBS buffer; 2x 5 min), 11. Substrate (FAST Red / New Fuchsin; see applicable IFU), 12. Wash aqua dest (Wash; 2x 2 min), 13. Counterstain and coverslip with a aqueous mounting medium (Auxiliary)
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
The BrightDiluents universal IHC diluent is specially formulated to stabilize antibodies and eliminate backgrounds encountered in immunohistochemistry staining procedures. The diluent contains complex proteins and non-protein mixtures which eliminate histostaining background by blocking Fc receptors and prevents non-specific protein-protein interactions. It can also be used as blocking applied before primary antibodies. If primary antibodies are diluted in this diluent, a blocking step before primary antibodies can generally be omitted. The blocking /diluent solution is supplied in Ready-to-Use format. It should not be diluted to be effective. The diluent contains no azide, therefore, it can be used to dilute and stabilize HRP-conjugates as well as any other solution that need and stabilizing carrier protein, such as Blocking and Poly-AP conjugates. This product should be interpreted by a qualified pathologist with relevant clinical information, morphological and histological studies and with proper controls. The ready-to-use antibody diluent is available in different colors: MON-APP917 (Transparant/colorless), MON-APP917B (Blue), MON-APP917Y (Yellow), MON-APP917G (green), MON-APP917R (Red)
Principle of method:
Antibody diluent
Reagents provided:
125 ml BrightDiluent, normal antibody diluent (ready-to-use)
For in-vitro Diagnostic Use. The BrightVision one step detection system Goat Anti-Rabbit IgG AP, is intended for use in immunohistochemistry for the detection of rabbit antibodies.
The BrightVision detection system Goat Anti-Rabbit AP, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision detection system detects Rabbit bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen (not provided). Also available in 110 ml, 500 ml and 1000 ml.
Principle of method:
One step detection system goat anti-rabbit IgG AP
Reagents provided:
One step detection system Goat anti-Rabbit AP (Ready-to-use; 55 ml)
Storage and handling:
2-8°C and in the dark
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary rabbit antibody (Antibody; 30 min), 8. Wash buffer (TBS buffer; 2x 5 min), 9. Detection system, polymer Rabbit AP, (Labeled polymer; 30 min), 10. Wash buffer (TBS buffer; 2x 5 min), 11. Substrate (Fast Red / New Fuchsin; see applicable IFU), 12. Wash aqua dest (Wash; 2x 2 min), 12. Counterstain and coverslip with aqueous mounting medium.
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
The Plus AP Kit, Rabbit is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from rabbit. The Plus AP Kit, Rabbit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Kit, Rabbit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and alkaline phosphatase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus AP Kit, Rabbit binds to rabbit primary antibodies. Therefore this kit can detect mono- and polyclonal primary antibodies and sera obtained from rabbit.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This antibody functions as a link between primary antibody and streptavidin-alkaline phosphatase-conjugate (Streptavidin-AP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-AP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent Red (included only in kit MON-APP128) leads to the formation of a magenta-red product of reaction at the place of the target antigen. Other suitable chromogens are Permanent AP Red (magenta-red) or NBT (blue-black) with its substrate BCIP.
Reagents provided:
8 ml Blocking Solution Reagent 1 (ready-to-use) 8 ml Biotinylated Secondary Antibody, Rabbit Reagent 2 (ready-to-use) 8 ml Streptavidin-AP-Conjugate Reagent 3 (ready-to-use) 8 x 5 ml Permanent Red Buffer (Substrate Buffer) 2 ml Permanent Red Concentrate (Chromogen) Substrate systems recommended (if not included in the kit) Permanent AP Red kit, BCIP/NBT Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate working solution (with MON-APP128 only): Add 2 drops (60 µl) of Permanent Red Concentrate to one bottle of Permanent Red Buffer (Substrate Buffer) and mix. This solution should be used directly after preparation.
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 2 min. 5. Biotinylated Secondary Antibody, Rabbit (Reagent 2, yellow) 10-15 min. 6. Washing with wash buffer 3 x 2 min. 7. Streptavidin-AP-Conjugate (Reagent 3, red) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent Red substrate-chromogen solution (with AP008RED-RB) 5 min. 10. Wash with distilled H2O 1 min. 11. Permanent Red substrate-chromogen solution (with AP008RED-RB) 5 min. 12. Wash with destilled water 3 x 1 min. 13. Counterstaining and blueing 14. Mounting: aqueous or permanent after dehydration * The incubation times should be adjusted, when using other substrate-chromogen systems
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from rabbit, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see section Limitations of the Procedure). 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific binding.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) for the pure substances are available upon request. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear.
The blocking solution Peroxide Block is intended for inhibition of endogenous peroxidase activity in tissue sections. It is primarily intended to be used in immunohistochemistry on formalin-fixed paraffin-embedded samples if using a detection system with horse radish peroxidase.
Endogenous peroxidase activity in the tissue can result in unspecific background staining in immunohistochemical staining procedures using horse radish peroxidase (HRP) as detection enzyme. This effect can be eliminated when tissue sections are incubated with Peroxide Block prior to immunohistochemical staining. Hydrogen peroxide in the solution blocks the activity of endogenous peroxidase.
Principle of method:
Peroxide Block is applied onto tissue sections to reduce non-specific staining due to endogenous peroxidase activity in immunohistochemistry. The step is carried out before incubation with primary antibody but after dewaxing and rehydration. If a heat induced epitope retrieval (HIER) or enzymatic digestion is necessary for immunohistochemical detection it is of no importance if the Peroxide Block is used before or after this step. In some cases it has been shown, that blocking of endogenous peroxidase before the epitope retrieval leads to better results.
Reagents provided:
8 ml Peroxide Block (ready-to-use)
Storage and handling:
The solution should be stored at 2-8°C without furt her dilution. Please store the reagent in a dark place and do not freeze it. Avoid exposure to strong light. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Procedure:
1. Apply Peroxide Block for 10 minutes at room temperature. The section should be covered completely. 2. Rinse with wash buffer. 3. Proceed with next steps for immunohistochemical staining as usual starting with protein blocking or the primary antibody.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, contact our technical support. Also refer to the instructions of the detection systems containing Peroxide Block for guidance on general troubleshooting
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific binding. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent or specimen with eye, skin or mucous membrane. In case of the reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. A material safety data sheet (MSDS) is available upon request
The Plus AP Polymer Kit is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. It is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mice and rabbits. The kit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus AP Polymer Kit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer in this kit consists of several molecules of secondary antibodies covalently bound to several molecules of alkaline phosphatase (AP). Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The test system is suitable for the detection of mono- and polyclonal primary antibodies and sera obtained from mice and rabbits. In contrast to other detection techniques, which often use the streptavidin-biotin system the Plus AP Polymer Kit avoids the problem of background staining caused by endogenous biotin in the tissue.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the AP polymer is minimized by incubation with a protein blocking solution (Blocking Solution, provided with this kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the enhancement reagent (PostBlock) is applied and incubated. A second washing is followed by the application of the AP-polymer. Any excess of unbound APpolymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent AP Red leads to the formation of a magentared product of reaction at the place of the target antigen.
Reagents provided:
100 ml Blocking Solution Reagent 1 (ready-to-use) 100 ml PostBlock Reagent 2 (ready-to-use) 100 ml AP-Polymer (Mouse/Rabbit) Reagent 3 (ready-to-use) Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support.
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out
Procedure:
1. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 5 min. 5. PostBlock (Reagent 2, yellow) 20 min. 6. Washing with wash buffer 3 x 5 min. 7. AP-polymer (Reagent 3, red) 30 min. 8. Washing with wash buffer 3 x 2 min. 9. Permanent AP Red 10-20 min. (Controlling the colour intensity via light microscope is recommended.) 10. Stopping the reaction with distilled H2O when the desired colour intensity is attained 11. Counterstaining and blueing 12. Mounting: permanent or aqueous with Permanent AP Red
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse or rabbit, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. If you are using PBS-based wash buffer: the activity of alkaline phosphatase in the reagents is blocked if too much wash buffer remains on the slides. 7. Incubation times were too short or primary antibody concentration too low. 8. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous alkaline phosphatase in the tissue. This undesired activity can often be suppressed using levamisole (see section Limitations of the Procedure).
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous alkaline phosphatase activity may cause non-specific staining. The enzyme activity can be blocked by incubation with levamisole. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Therefore, tissues of this origin should be stained with peroxidase detection systems (i.e. POLHRP-125). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the BlockingSolution instead of just draining it away as in other procedures. We will guarantee that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and ProClin 950 used for stabilisation. Material safety data sheets (MSDS) are available upon request.
The Plus HRP Kit, Broad Spectrum is based on the streptavidin-biotin system. It is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mouse, rabbit, rat, and guinea pig. The Plus HRP Kit, Broad Spectrum can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Kit, Broad Spectrum is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and horse radish peroxidase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus HRP Kit, Broad Spectrum is polyvalent. Therefore this kit can detect mono- and polyclonal primary antibodies and sera obtained from mouse, rabbit, rat, and guinea pig.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide Block). Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and the streptavidin-horse radish peroxidase-conjugate (Streptavidin-HRP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-HRP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC (included only in kit MON-APP114) leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB (included only in kit MON-APP115) forms a dark brown precipitate.
Reagents provided:
8 ml Peroxide Block (ready-to-use) 8 ml Blocking Solution Reagent 1 (ready-to-use) 8 ml Biotinylated Secondary Antibody, polyvalent Reagent 2 (ready-to-use) 8 ml Streptavidin-HRP-Conjugate Reagent 3 (ready-to-use) 7 x 5 ml DAB Substrate Buffer 3 ml DAB Concentrate (Chromogen) Substrate systems recommended (if not included in the kit): Permanent AEC kit, AEC single solution, AEC substrate kit, DAB substrate kit, DAB high contrast kit. Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support.
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. The tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate AEC working solution (with MON-APP114 only): Add 2 drops (100 µl) of AEC Concentrate to one bottle of AEC Substrate Buffer and mix thoroughly. Preparation of the chromogenic substrate DAB working solution (with MON-APP115 only): Add 4 drops (200 µl) of DAB Concentrate to one bottle of DAB Substrate Buffer and mix thoroughly.
Procedure:
1. Peroxide Block (3% H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 2 min. 7. Biotinylated Secondary Antibody, polyvalent (Reagent 2, yellow) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Streptavidin-HRP-Conjugate (Reagent 3, red) 10-15 min. 10. Washing with wash buffer 3 x 2 min. 11. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 12. Stopping the reaction with distilled H2O when the desired colour intensity is attained 13. Counterstaining and blueing 14. Mounting: aqueous with AEC, permanent with DAB or Permanent AEC
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support . No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse, rabbit, rat or guinea pig. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase. Maybe the hydrogen peroxide solution used for blocking was inactivated. 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with 3% H2O2 solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Background staining due to endogenous biotin can be blocked through an avidinbiotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) are available upon request.
The Plus HRP Kit, Rabbit is based on the streptavidin-biotin system. It is designed for qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from rabbit. The Plus HRP Kit, Rabbit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Kit, Rabbit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and horse radish peroxidase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus HRP Kit, Rabbit binds to rabbit primary antibodies. Therefore this kit can detect mono- and polyclonal primary antibodies and sera obtained from rabbit.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide Block). Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This antibody functions as a link between primary antibody and the streptavidin-horse radish peroxidase-conjugate (Streptavidin-HRP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-HRPconjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC (included only in kit MON-APP132) leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB (included only in kit MON-APP133) forms a dark brown precipitate.
Reagents provided:
4x 15 ml Blocking Solution Reagent 1 (ready-to-use) 4x 15 ml Biotinylated Secondary Antibody, Rabbit Reagent 2 (ready-to-use) 4x 15 ml Streptavidin-HRP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit): Permanent AEC kit, AEC Single Solution, AEC substrate kit, DAB Substrate kit, DAB High Contrast kit Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Procedure:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. The tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate AEC working solution (with MON-APP132 only): Add 2 drops (100 µl) of AEC Concentrate to one bottle of AEC Substrate Buffer and mix thoroughly. Preparation of the chromogenic substrate DAB working solution (with MON-APP133 only): Add 4 drops (200 µl) of DAB Concentrate to one bottle of DAB Substrate Buffer and mix thoroughly.
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from rabbit. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase. Maybe the hydrogen peroxide solution used for blocking was inactivated. 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with 3% H2O2 solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Background staining due to endogenous biotin can be blocked through an avidinbiotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) are available upon request.
For in-vitro Diagnostic Use. The BrightVision Ultimate plus two steps component detection system peroxidase Goat Anti-Mouse/Rabbit IgG HRP and DAB, is intended for use in immunohistochemistry for the detection of mouse or rabbit antibodies.
The BrightVision Ultimate plus detection system, peroxidase Goat Anti-Mouse/Rabbit HRP plus DAB, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision Ultimate plus detection system detects Mouse or Rabbit bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen. The clinical interpretation of any staining or its absence should be determined by a qualified pathologist and complemented by morphologic studies; controls should be evaluated within the context of the patients clinical history and/or other diagnostic tests.
Principle of method:
BrightVision Ultimate plus, two steps detection system, Goat Anti-Mouse/Rabbit HRP (Ready-to-Use) plus DAB.
Reagents provided:
BrightVision Ultimate plus, two steps detection system, Goat Anti-Mouse/Rabbit HRP (Ready-to-Use) plus DAB 1. Post-blocking (ready-to-use): 55 ml 2. Polymer Goat Anti-Mouse/Rabbit HRP (Ready-to-Use): 55 ml 3. DAB Solution A: Buffered H2O2 (Ready-to-Use): 83 ml 4. DAB Solution B: Concentrated DAB solution: 4 ml
Storage and handling:
2-8°C and in the dark
Reagent preparation:
Preparation DAB: Add 40?l DAB Solution B (one drop) to 1 ml substrate Solution A, mix well. Volume and the quality of the Bright DAB has been formulized so they also can be used in automatic stainers, when a higher volume is required.
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary mouse or rabbit antibody (Antibody; 30 min), 8. Wash buffer (PBS or TBS buffer; 2x 5 min), 9. Detection system, step 1, post-blocking (Post-blocking; 15 min), 10 Wash buffer (PBS or TBS buffer; 2x 5 in). 11 Detection system, step 2, polymer Mouse/Rabbit HRP, (Labeled polymer; 30 min), 12. Wash buffer (PBS or TBS buffer; 2x 5 min), 13. Substrate (DAB; 8 min; Preparation DAB: Add 40?l DAB Solution B (one drop) to 1 ml substrate Solution A, mix well. Volume and the quality of the Bright DAB has been formulized so they also can be used in automatic stainers, when a higher volume is required.), 14. Wash aqua dest (Wash; 2x 2 min), 15. Counterstain, dyhydrate and coverslip (Auxiliary.
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
CryoCompound freezing medium is an aqueous based frozen tissue embedding medium designed to support tissue blocks in cryostat sectioning. Formulated to promote rapid freezing, enhanced sectioning and consistent results at a working temperature of -20° C. The ready-to-use Cryocompound is available in different colors: MON-APP900C (Transparant/colorless), MON-APP900B (Blue), MON-APP900Y (Yellow), MON-APP900O (Orange), MON-APP900G (green), MON-APP900R (Red) or Multicolorkit MON-APP900BYGR (Blue, Yellow, Green, Red).
Principle of method:
Freezing medium
Reagents provided:
100 ml Cryocompound, freezing medium (ready-to-use)
Storage and handling:
Store at room temperature
Procedure:
1. Place few drops of CryoCompound (depends on the size of the sample to be embedded) onto the center of the bottom of cryomold. Be careful to select the proper size embedding mold according to the size of the sample to be embedded. 2. Try to avoid the formation of air bubbles. Remove any bubbles inside the CryoCopound. This is important because the air bubbles will create problems when cutting sections. Air bubbles create freeze- thaw-freeze cycle and ice crystal will form inside of it and result in a very bad morphology due to the ice crystal artefact. 3. Let it settle for 15-30 seconds to allow the CryoCompound to completely wet the surface of the tissue. Hardening of the CryoCompound included the sample (it will happen in 0.5-1 minute) before preparing the CryoCompoundsample-block.
The BrightDiluents universal IHC diluent is specially formulated to stabilize antibodies and eliminate backgrounds encountered in immunohistochemistry staining procedures. The diluent contains complex proteins and non-protein mixtures which eliminate histostaining background by blocking Fc receptors and prevents non-specific protein-protein interactions. It can also be used as blocking applied before primary antibodies. If primary antibodies are diluted in this diluent, a blocking step before primary antibodies can generally be omitted. The blocking /diluent solution is supplied in Ready-to-Use format. It should not be diluted to be effective. The diluent contains no azide, therefore, it can be used to dilute and stabilize HRP-conjugates as well as any other solution that need and stabilizing carrier protein, such as Blocking and Poly-AP conjugates. This product should be interpreted by a qualified pathologist with relevant clinical information, morphological and histological studies and with proper controls. The ready-to-use antibody diluent is available in different colors: MON-APP917 (Transparant/colorless), MON-APP917B (Blue), MON-APP917Y (Yellow), MON-APP917G (green), MON-APP917R (Red)
Principle of method:
Antibody diluent
Reagents provided:
125 ml BrightDiluent, normal antibody diluent (ready-to-use)
The Plus HRP Polymer Kit is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. It is developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mice and rabbits. The kit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Polymer Kit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer in this kit consists of several molecules of secondary antibodies covalently bound to several molecules of horse radish peroxidase (HRP). Visualisation occurs via an enzyme-substrate reaction in the presence of a colorising reagent which permits microscopical analysis. The test system is suitable for the detection of mono- and polyclonal primary antibodies and sera obtained from mice and rabbits. In contrast to other detection techniques, which often use the streptavidin-biotin system the Plus HRP Polymer Kit avoids the problem of background staining caused by endogenous biotin in the tissue
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (peroxide block). Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the HRPpolymer is minimized by incubation with a protein blocking solution (Blocking Solution, provided with the kit). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the enhancement reagent (PostBlock) is applied and incubated. A second washing is followed by the application of the HRP-polymer. Any excess of unbound HRP-polymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB forms a dark brown precipitate.
Reagents provided:
6 ml Blocking Solution Reagent 1 (ready-to-use) 6 ml PostBlock Reagent 2 (ready-to-use) 6 ml HRP-Polymer (Mouse/Rabbit) Reagent 3 (ready-to-use) Substrate systems recommended: Permanent AEC kit, AEC single solution, AEC substrate kit, DAB substrate kit, DAB High contrast kit. Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support.
Reagent preparation:
Reagents should be at room temperature when used. ? Deparaffinise and rehydrate paraffin-embedded tissue sections. ? Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. ? Tissue sections have to be completely covered with the different reagents in order to avoid drying out.
Procedure:
1. Peroxide blocking (3 % H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 5 min. 7. PostBlock (Reagent 2, yellow) 20 min. 8. Washing with wash buffer 3 x 5 min. 9. HRP-polymer (Reagent 3, red) 30 min. 10. Washing with wash buffer 3 x 2 min. 11. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 12. Stopping the reaction with distilled H2O when the desired colour intensity is attained 13. Counterstaining and blueing 14. Mounting: aqueous with AEC, permanent with DAB
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support . No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse or rabbit, but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Nonspecific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase in the tissue. Maybe the hydrogen peroxide solution used for blocking was inactivated.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity may cause non-specific staining. The enzyme activity is blocked by incubation with hydrogen peroxide solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. We guarantee that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin is used for stabilisation. A material safety data sheet is available upon request.
The Plus HRP Kits, Mouse is based on the streptavidin-biotin system. It is designed for qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with monoclonal primary antibodies and sera obtained from mice. The Plus HRP Kit, Mouse can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Kit, Mouse is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and horse radish peroxidase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus HRP Kit, Mouse binds to mouse primary antibodies. Therefore this kit can detect monoclonal primary antibodies and sera obtained from mice.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide Block). Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and the streptavidin-horse radish peroxidase-conjugate (Streptavidin-HRP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-HRP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed via a light microscope. The chromogen used determines the colour. The chromogen AEC (included only in kit MON-APP123) leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB (included only in kit MON-APP124) forms a dark brown precipitate.
Reagents provided:
125 ml Blocking Solution Reagent 1 (ready-to-use) 125 ml Biotinylated Secondary Antibody, Mouse Reagent 2 (ready-to-use) 125 ml Streptavidin-HRP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit): Permanent AEC kit, AEC single solution, AEC substrate kit, DAB substrate kit, DAB high contrast kit. Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. The tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate AEC working solution (with MON-APP123 only): Add 2 drops (100 µl) of AEC Concentrate to one bottle of AEC Substrate Buffer and mix thoroughly. Preparation of the chromogenic substrate DAB working solution (with MON-APP124 only): Add 4 drops (200 µl) of DAB Concentrate to one bottle of DAB Substrate Buffer and mix thoroughly
Procedure:
1. Peroxide Block (3% H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 2 min. 7. Biotinylated Secondary Antibody, Mouse (Reagent 2, yellow) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Streptavidin-HRP-Conjugate (Reagent 3, red) 10-15 min. 10. Washing with wash buffer 3 x 2 min. 11. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 12. Stopping the reaction with distilled H2O when the desired colour intensity is attained 13. Counterstaining and blueing 14. Mounting: aqueous with AEC, permanent with DAB or Permanent AEC
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase. Maybe the hydrogen peroxide solution used for blocking was inactivated. 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with 3% H2O2 solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Background staining due to endogenous biotin can be blocked through an avidinbiotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) are available upon request.
The Plus HRP Kits, Mouse is based on the streptavidin-biotin system. It is designed for qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. The kit is developed for use in combination with monoclonal primary antibodies and sera obtained from mice. The Plus HRP Kit, Mouse can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Kit, Mouse is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The method is based on the streptavidin-biotin system which means that a biotinylated secondary antibody binds to several molecules of a conjugate composed of streptavidin and horse radish peroxidase. Visualisation occurs via an enzyme-substrate reaction in the presence of a colourising reagent which permits microscopical analysis. The biotinylated secondary antibody in the Plus HRP Kit, Mouse binds to mouse primary antibodies. Therefore this kit can detect monoclonal primary antibodies and sera obtained from mice.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (Peroxide Block). Background staining caused by unspecific binding of the primary or secondary antibody is minimized by incubation with a protein blocking solution (Blocking Solution). This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the biotinylated secondary antibody is applied and incubated. This secondary antibody functions as a link between primary antibody and the streptavidin-horse radish peroxidase-conjugate (Streptavidin-HRP-Conjugate). A second washing is followed by the application of this conjugate. It binds to the biotin at the secondary antibody. Any excess of unbound streptavidin-HRP-conjugate is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the horse radish peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed via a light microscope. The chromogen used determines the colour. The chromogen AEC (included only in kit MON-APP123) leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB (included only in kit MON-APP124) forms a dark brown precipitate.
Reagents provided:
500 ml Blocking Solution Reagent 1 (ready-to-use) 500 ml Biotinylated Secondary Antibody, Mouse Reagent 2 (ready-to-use) 500 ml Streptavidin-HRP-Conjugate Reagent 3 (ready-to-use) Substrate systems recommended (if not included in the kit): Permanent AEC kit, AEC single solution, AEC substrate kit, DAB substrate kit, DAB high contrast kit. Materials required but not supplied Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. They should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. The tissue sections have to be completely covered with the different reagents in order to avoid drying out. Preparation of the chromogenic substrate AEC working solution (with MON-APP123 only): Add 2 drops (100 µl) of AEC Concentrate to one bottle of AEC Substrate Buffer and mix thoroughly. Preparation of the chromogenic substrate DAB working solution (with MON-APP124 only): Add 4 drops (200 µl) of DAB Concentrate to one bottle of DAB Substrate Buffer and mix thoroughly
Procedure:
1. Peroxide Block (3% H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (protein block, Reagent 1) (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 2 min. 7. Biotinylated Secondary Antibody, Mouse (Reagent 2, yellow) 10-15 min. 8. Washing with wash buffer 3 x 2 min. 9. Streptavidin-HRP-Conjugate (Reagent 3, red) 10-15 min. 10. Washing with wash buffer 3 x 2 min. 11. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 12. Stopping the reaction with distilled H2O when the desired colour intensity is attained 13. Counterstaining and blueing 14. Mounting: aqueous with AEC, permanent with DAB or Permanent AEC
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse. 6. The antigen was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pretreatment or enzyme digestion. If you used a pre-treatment it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Non-specific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme conjugate or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase. Maybe the hydrogen peroxide solution used for blocking was inactivated. 9. Non-specific binding of the secondary antibody to endogenous biotin in the tissue section. Carry out an avidin-biotin block before incubation with the primary antibody.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity or the endogenous biotin content may cause non-specific staining. The enzyme activity can be blocked by incubation with 3% H2O2 solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Background staining due to endogenous biotin can be blocked through an avidinbiotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution (Blocking Solution) can result in decreasing signal intensity. Therefore, we recommend washing away the Blocking Solution instead of just draining it away as in other procedures. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 and sodium azide (NaN3) are used for stabilisation. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. Material safety data sheets (MSDS) are available upon request.
The TRIS/EDTA buffer, is designed for use during heat-induced epitope retrieval (HIER) on formalinfixed paraffin-embedded tissue sections prior to antibody application. In immunohistochemistry (IHC), protein cross-links are formed during formalin or other aldehyde fixation. These cross-links mask the antigenic sites in tissue specimens and results in weak or false negative staining in immunohistochemical detection of proteins. The use of this citrate buffer in combination with heat ensures that the antigenicity of proteins modified, thus enhancing staining intensity of antibodies. For the recommended pre-treatment technique, please refer to the individual antibody's instructions for use. This buffer is a 10x concentrate solution and must be diluted 1:10 with deionized water before using. The final readyto-use solution should have a pH of 9.0 ± 0.3. The buffer can be used for a maximum of three runs within five days after dilution. Also available in 250 ml, 500 ml en 1000 ml.
Principle of method:
Heat-Induced Epitope Retrieval
Reagents provided:
100 ml 10x concentrate solution. TRIS/EDTA buffer, Heat-Induced Epitope Retrieval (10x, Tween20), Blue
Storage and handling:
Store at room temperature
Reagent preparation:
Before use dilute 1:10 with deionized water. The final ready-to-use solution should have a pH of 9.0 ± 0,3,
Procedure:
1. Deparaffinize and rehydrate the tissue slides. 2. Fill the PT Module tank with 150 ml of TRIS?EDTA buffer and 1,350 ml of deionized water, to obtain 1,500 ml of ready-to-use solution (1:10 dilution). 3. Pre-heat the PT Module until temperature reaches 65°C and place the formalin-fixed slides in slide racks into the PT Module tank. 4. Heat the TRIS/EDTA buffer and slides to 98°C and incubate for 15 minutes. 5. Cool slides in the PT Module to 65°C. 6. Remove slides and cool to room temperature for at least 5 minutes in a PBS or TBS based buffer. 7. Continue with staining according to IHC protocol. Note: Alternative heating sources, such as a microwave or a pressure cooker, can be used to replace the PT Module tank. The optimal incubation time for these heating sources should be determined by authorised personnel / researchers.
The Citrate buffer, is designed for use during heat-induced epitope retrieval (HIER) on formalinfixed paraffin-embedded tissue sections prior to antibody application. In immunohistochemistry (IHC), protein cross-links are formed during formalin or other aldehyde fixation. These cross-links mask the antigenic sites in tissue specimens and results in weak or false negative staining in immunohistochemical detection of proteins. The use of this citrate buffer in combination with heat ensures that the antigenicity of proteins modified, thus enhancing staining intensity of antibodies. For the recommended pre-treatment technique, please refer to the individual antibody's instructions for use. This buffer is a 10x concentrate solution and must be diluted 1:10 with deionized water before using. The final readyto-use solution should have a pH of 6.0 ± 0.3. The buffer can be used for a maximum of three runs within five days after dilution. Also available in 250 ml, 500 ml en 1000 ml.
Principle of method:
Heat-Induced Epitope Retrieval
Reagents provided:
100 ml 10x concentrate solution. Citrate buffer, Heat-Induced Epitope Retrieval (10x, Tween20), Red
Storage and handling:
Store at room temperature
Reagent preparation:
Before use dilute 1:10 with deionized water. The final ready-to-use solution should have a pH of 6.0 ± 0,3,
Procedure:
1. Deparaffinize and rehydrate the tissue slides. 2. Fill the PT Module tank with 150 ml of citrate buffer and 1,350 ml of deionized water, to obtain 1,500 ml of ready-to-use solution (1:10 dilution). 3. Pre-heat the PT Module until temperature reaches 65°C and place the formalin-fixed slides in slide racks into the PT Module tank. 4. Heat the citrate buffer and slides to 98°C and incubate for 20 minutes. 5. Cool slides in the PT Module to 65°C. 6. Remove slides and cool to room temperature for at least 5 minutes in a PBS or TBS based buffer. 7. Continue with staining according to IHC protocol. Note: Alternative heating sources, such as a microwave or a pressure cooker, can be used to replace the PT Module tank. The optimal incubation time for these heating sources should be determined by authorised personnel / researchers.
HIER Citrate Buffer pH 6.0 is a solution developed for heat induced epitope retrieval (HIER) in formalin-fixed paraffin-embedded tissue sections on slides. This procedure is primarily used in immunohistochemistry.
Immunohistochemical staining procedures consist of sequential incubation steps with blocking solutions, antibodies and secondary reagents, enzymes and chromogenic substrates carried out on tissue sections. These tissue sections are mostly prepared out of formalin-fixed paraffin-embedded tissue blocks. Cellular structures are very effectively stabilised by formalin fixation which results in optimal morphological preservation of the sample. On the other hand the formalin fixation leads to strong cross-links between proteins. This means that epitopes of antigens are being masked and often are no longer accessible for primary antibodies. In order to enable primary antibodies to bind to the antigens the epitopes have to be recovered. Heat induced epitope retrieval (HIER) in buffer solutions of different compositions and pH-values restore structures of the epitopes making them more accessible to specific antibodies. Enzymatic digestion with proteolytic enzymes is another way of recovering epitopes. The primary antibody used determines the appropriate method.
Principle of method:
HIER Citrate Buffer pH 6.0 is a 10fold concentrated citrate buffer solution with additives of stabilising substances. For preparation of the working strength solution the buffer concentrate is diluted 1:10 with deionised or distilled water. The resulting solution has a pH of 6.0 (5.8 to 6.2). HIER Citrate Buffer pH 6.0 is a very efficient epitope retrieval solution in immunohistochemical staining procedures to be used with primary antibodies of many different specificities.
Reagents provided:
500 ml HIER Citrate Buffer pH 6.0 (10fold concentrated, adequate for 5 litres ready-to-use citrate buffer)
Storage and handling:
The solution should be stored at 2-8°C. Do not free ze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. If stored at room temperature the solution is stable for at least 10 month from the date of delivery. The prepared working strength solution is stable for 1 month, if stored at 2-8°C. A positive and a negat ive control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Reagent preparation:
Preparation of the citrate buffer working strength solution: Dilute HIER Citrate Buffer concentrate 1:10 with deionised or distilled water and mix thoroughly. The pH-value should be at 6.0 (5.8 to 6.2). If necessary adjust pH-value with diluted NaOH or HCl solution.
Procedure:
HIER Citrate Buffer is suitable for various HIER-methods such as steamer, pressure cooker, autoclave, water bath, and microwave oven. Tissue sections used in heat induced epitope retrieval should always be placed on adhesive slides. Epitope retrieval is carried out after dewaxing and rehydration of the sections. Exemplary protocol using steamer: 1. Prepare the working strength solution by diluting the buffer concentrate as described above and transfer to a Coplin jar. Please make sure that there is enough volume to cover the tissue sections on the slides completely. 2. Fill steamer with water according to instruction manual, close lid and start. 3. After 10 minutes place Coplin jar with citrate buffer in the steamer, close the lid and heat the solution for 20 minutes. 4. Place slides with tissue sections into the preheated solution and close the lid. Tissue sections have to be completely covered with citrate buffer solution. 5. Incubate slides 20 40 minutes. The optimal incubation time needs to be elaborated by the operator. 6. After the incubation take the Coplin jar with slides out of steamer and let cool down at room temperature for about 20 minutes. 7. Remove citrate buffer, rinse slides with wash buffer and proceed with immunohistological staining.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific binding. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent or specimen with eye, skin or mucous membrane. In case of the reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. ProClin 300 is used for stabilisation. A material safety data sheet (MSDS) is available upon request.
For in-vitro Diagnostic Use. The BrightVision two components detection system peroxidase Goat Anti-Mouse/Rabbit IgG AP, is intended for use in immunohistochemistry for the detection of mouse or rabbit antibodies.
The BrightVision detection system peroxidase Goat Anti- Mouse/Rabbit AP, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision detection system detects Mouse or Rabbit bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen (not provided).
Principle of method:
Two steps detection system goat anti-mouse/rabbit AP
Reagents provided:
Post-blocking (ready-to-use) (Gold) 55 ml and Polymer Goat Anti-Mouse/Rabbit AP (ready-to-use) (Ruby) 55 ml.
Storage and handling:
2-8°C and in the dark
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary mouse or rabbit antibody (Antibody; 30 min), 8. Wash buffer (PBS or TBS buffer; 2x 5 min), 9. Detection system, step 1, post-blocking (Post-blocking; 15 min), 10. Wash buffer (PBS or TBS buffer; 2x 5 min), 11. Detection system, step 2, polymer Mouse/Rabbit AP (Labeled polymer; 30 min), 12. Wash buffer (PBS or TBS buffer; 2x 5 min), 13. If applicable Substrate (DAB), 14. Wash aqua dest (Wash; 2x 2 min), 15. Counterstain, dehydrate and coverslip (Auxiliary)
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
Permanent AP Red Kit is developed for immunohistochemical and in situ-hybridisation staining procedures with alkaline phosphatase. Permanent AP Red leads to the formation of a magenta-red precipitate at the location of the target antigen or target nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light or fluorescence microscopy.
125 ml Permanent AP Red Buffer 2 ml Permanent AP Red Chromogen 1 Dilution Vial
Storage and handling:
The solutions should be stored at 2-8°C without further dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. Do not use product after the expiry date. The working solution prepared is stable for about 60 minutes and should therefore be used directly after preparation. Excess working solution should be discarded. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
Reagent preparation (Preparation of the working solution) 1) Pipette 2.5 ml AP Red Buffer into the provided dilution vial and let it come to room temperature. The chromogen should still be kept cool. 2) Directly prior to use add 1 drop of Permanent AP Red Chromogen into the buffer. Mix thoroughly. 3) The solution is stable for about 60 minutes. Preparation should be done directly before use. Make sure to pipet the chromogen/substrate mix on the last slide of the staining run within 40 min after mixing. If you want to prepare other quantities of the working solution, please use same ratio AP Red Buffer and Chromogen
Procedure:
1) Rinse the slide with wash buffer after the previous incubation step. 2) Apply freshly prepared Permanent AP Red working solution onto the slide. Incubate for 10 minutes. 3) Rinse with distilled H2O. 4) Counterstain with haematoxylin for about 30 seconds up to 5 minutes (depending on the desired staining intensity). 5) Rinse with distilled H2O. 6) Blueing in tap water for at least 5 minutes. 7) Dehydrate through a graded series of ethanol and clear in xylene. Mount with a permanent mounting medium. Note: It is also possible to mount Permanent AP Red with aqueous mounting media.
Expected results:
During the reaction of the substrate with alkaline phosphatase in presence of the chromogen Permanent AP Red, a magenta-red precipitate is formed at the location of the target antigen or nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light or fluorescence microscopy (Texas Red filter).
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). In some tissues endogenous alkaline phosphatase activity may cause non-specific staining. However, neither intestinal nor placental alkaline phosphatase can be blocked with levamisole. Therefore, tissues of this origin should be stained with peroxidase detection systems. A higher sensitivity can be obtained when a second chromogenic substrate step is used (i. e. 2 x 10 min Permanent AP Red). Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. A longer exposure to absolute ethanol can result in decreasing staining intensity. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagents or specimen with eye, skin or mucous membrane. In case of a reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. A material safety data sheet (MSDS) is available upon request.
The Fast AP One-Step Polymer anti-Mouse/Rabbit is designed for the qualitative detection of antigens in fixed paraffin-embedded tissue sections, in frozen tissue sections, and in cytological samples. It was developed for use in combination with mono- and polyclonal primary antibodies and sera obtained from mice or rabbit. The kit can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE. It is intended for in vitro diagnostic use.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Fast AP One-Step Polymer anti-Mouse/Rabbit is a highly sensitive detection reagent intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer consists of several molecules of secondary antibodies covalently bound to several molecules of alkaline phosphatase (AP). Visualisation occurs via an enzymesubstrate reaction in the presence of a colorising reagent which permits microscopical analysis. The test system is suitable for the detection of mono- and polyclonal primary antibodies and sera obtained from mice or rabbit. Cross-reactivity with primary antibodies from rat has been observed. In contrast to other detection techniques, which often use the streptavidin-biotin system the Fast AP One-Step Polymer anti-Mouse/Rabbit avoids the problem of background staining caused by endogenous biotin in the tissue.
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the AP OneStep Polymer is minimized by incubation with a protein blocking solution. This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the AP One-Step Polymer is applied and incubated. Any excess of unbound polymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the alkaline phosphatase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen Permanent AP Red leads to the formation of a magentared product of reaction at the place of the target antigen.
Reagents provided:
6 ml Fast AP One-Step Polymer anti-Mouse/Rabbit (ready-to-use) Substrate systems recommended: Permanaent AP Red kit Materials required but not supplied Positive and negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS Blocking Solution (for protein blocking, optional) Pink PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date. It should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagent, please contact our technical support
Reagent preparation:
Reagents should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out.
Procedure:
1. Blocking Solution (This step is optional.) 5 min. 2. Washing with wash buffer 1 x 2 min. 3. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 4. Washing with wash buffer 3 x 5 min. 5. AP One-Step Polymer anti-Mouse/Rabbit 30 Min. 6. Washing with wash buffer 3 x 2 min. 7. Permanent AP Red, 10-20 min. (Controlling the colour intensity via light microscope is recommended.) 8. Stopping the reaction with distilled H2O when the desired colour intensity is attained 9. Counterstaining and blueing 10. Mounting: permanent or aqueous with Permanent AP Red Kit
Expected results:
During the reaction of the substrate with alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support. No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse or rabbit but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Nonspecific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use Blocking Solution or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high).
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of a reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining might appear. ProClin 300 is used for stabilisation. A Material safety data sheet (MSDS) is available upon request.
Pepsin Solution is a ready-to-use solution developed for enzymatic epitope retrieval on formalin-fixed tissue sections on slides. This procedure (sometimes called PIER, Protease Induced Epitope Retrieval) is primarily used in immunohistochemical staining procedures.
Immunohistochemical staining procedures consist of sequential incubation steps with blocking solutions, antibodies and secondary reagents, enzymes and chromogenic substrates carried out on tissue sections. These tissue sections are mostly prepared out of formalin-fixed paraffin-embedded tissue blocks. Cellular structures are very effectively stabilised by formalin fixation which results in optimal morphological preservation of the sample. On the other hand the formalin fixation leads to strong cross-links between proteins. This means that epitopes of antigens are being masked and often are no longer accessible for primary antibodies. In order to enable primary antibodies to bind to antigens the epitopes have to be recovered. Enzymatic digestion with proteolytic enzymes (PIER) restores structures of the epitopes making them more accessible to specific antibodies. Heat induced epitope retrieval (HIER) in buffer solutions of different compositions and pH-values is another way of recovering epitopes. The primary antibody used determines the appropriate method.
Principle of method:
Pepsin Solution is a ready-to-use stabilised pepsin solution for enzymatic epitope retrieval.
Reagents provided:
60 ml Pepsin Solution (Ready-To-Use)
Storage and handling:
The solution should be stored at 2-8°C without furt her dilution. Do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support
Reagent preparation:
The solution is ready-to-use.
Procedure:
Pepsin Solution is suitable for enzymatic epitope retrieval carried out after the dewaxing and rehydration of the tissue sections. 1. Cover deparaffinised and rehydrated tissue sections with ready-to-use Pepsin Solution. 2. Incubate for 10 - 15 minutes at 37°C or 20 30 minutes at room temperature. The optimal incubation time needs to be elaborated by the operator. It was shown that in individual cases a stronger signal can be obtained when the incubation time is elongated up to 120 minutes (e. g. for detection of Collagen IV with different antibodies). 3. Rinse carefully (3 x) with wash buffer. 4. Proceed with immunohistological staining as usual.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent and specimen with eye, skin or mucous membranes. In case of reagent or specimen coming into contact with a sensitive area, wash area with large amounts of water. A material safety data sheet (MSDS) is available upon request.
DAB Substrate kit is intended for immunohistochemical and in situ-hybridisation staining procedures with horse radish peroxidase (HRP). DAB (3,3-Diaminobenzidine) leads to the formation of a brown precipitate at the location of the target antigen or target nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light microscopy.
3 ml DAB Chromogen (liquid DAB concentrate) 11 x 5 ml DAB Substrate Buffer
Storage and handling:
The solutions should be stored at 2-8°C without fur ther dilution. Please store the reagents in a dark place and do not freeze them. Under these conditions the solutions are stable up to the expiry date indicated on the label. Do not use product after the expiry date. The working solution should be prepared freshly at the day of use. Once the two reagents are combined, the resulting solution can be used for up to six hours. Excess working solution needs to be disposed as hazardous substance. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
Add 4 drops of DAB Chromogen (DAB concentrate) to one bottle of DAB Substrate Buffer and mix thoroughly.
Procedure:
1) Rinse the slide with wash buffer after the previous incubation step. 2) Apply the DAB working solution onto the slide. Incubate for 5-15 minutes. 3) Rinse with distilled H2O. 4) Counterstain with haematoxylin for about 30 seconds up to 5 minutes (depending on the desired staining intensity). 5) Rinse with distilled H2O. 6) Blueing in tap water for at least 5 minutes. 7) Dehydrate through a graded series of ethanol and clear in xylene. Mount with a permanent mounting medium. Note: It is also possible to mount DAB with aqueous mounting media.
Expected results:
During the reaction of the substrate with horse radish peroxidase in presence of the chromogen DAB, a brown precipitate is formed at the location of the target antigen or nucleic acid. The precipitate is insoluble in aqueous and organic solvents and can be observed by light microscopy.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). In some tissues endogenous peroxidase activity may cause non-specific staining. The enzyme activity should be blocked by incubation with hydrogen peroxide solution (H2O2 solution). The step is carried out before incubation with primary antibody but after dewaxing and rehydration. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. Inadequate counterstaining and mounting can influence the interpretation of the results. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. The DAB chromogen is hazardous to your health. Wear protective clothing to avoid contact of reagents or specimen with eye, skin or mucous membrane. In case of a reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagents must be avoided, since otherwise non-specific staining may occur. Material safety data sheets (MSDS) are available upon request.
The wash Buffer is designed as washing solution for immunohistochemical and immunocytological staining procedures on slides. Wash Buffer is primarily used with formalin-fixed paraffin-embedded tissue sections, but also with frozen, HOPE-fixed, and cytological samples as well as in immunoblot procedures. The Wash Buffer is suitable for manually operated and automated immunohistochemical staining.
Immunohistochemical staining procedures consist of sequential incubation steps with blocking solutions, antibodies and secondary reagents, enzymes and chromogenic substrates carried out on tissue sections. Washing away the applied reagents after each incubation step is critical to receive optimally stained samples. The Wash Buffer is especially designed for effective washing and therefore ensures brilliant staining results.
Principle of method:
The Wash Buffer is a 20fold concentrated phosphate buffer with additives of sodium chloride, detergent, and stabilising substances. For preparation of the working strength solution the buffer concentrate is diluted 1:20 with deionised or distilled water. The resulting solution has a pH of 7.2 (7.0 to 7.4). The Wash Buffer is wetting the tissue sections with detergent and thus reduces surface tension and improves spreading the reagents on the tissue section, reduces unspecific binding of reagents on the tissue sample, and because of the exact tuned salt concentration effects an excellent preservation of cell morphology.
Reagents provided:
2500 ml Wash Buffer (20fold concentrated, adequate for 50 litres ready-to-use wash buffer)
Storage and handling:
The solution should be stored at room temperature. It is stable up to the expiry date indicated on the label if undiluted. Do not use product after the expiry date. The diluted working strength solution is stable for about 1 week depending on the ambient temperature. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Reagent preparation:
Preparation of the Wash Buffer working strength solution: Dilute Wash Buffer concentrate 1:20 with deionised or distilled water and mix thoroughly. The pH-value should be at 7.2 (7.0 to 7.4). If necessary adjust pH-value with diluted NaOH or HCl solution.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results. The Wash Buffer is a 20fold concentrated solution with a mildly acidic pH-value. The correct pHvalue of about 7.0 (+/- 0.2) is achieved after diluting the solution 1:20. Sometimes deionised water has pH-values considerably different from the neutral point (pH 7.0) depending on the preparation method. Experiments have shown that the Wash Buffer can successfully be diluted with deionised or distilled with water in the pH-range of 5.5 up to 9.5. If a detection system with alkaline phosphatase is used please note: larger amounts of wash buffer remaining on the slides can lead to decreasing enzyme activity. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent or specimen with eye, skin or mucous membrane. In case of the reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. ProClin 300 is used for stabilisation. A material safety data sheet (MSDS) is available upon request.
CryoCompound freezing medium is an aqueous based frozen tissue embedding medium designed to support tissue blocks in cryostat sectioning. Formulated to promote rapid freezing, enhanced sectioning and consistent results at a working temperature of -20° C. The ready-to-use Cryocompound is available in different colors: MON-APP900C (Transparant/colorless), MON-APP900B (Blue), MON-APP900Y (Yellow), MON-APP900O (Orange), MON-APP900G (green), MON-APP900R (Red) or Multicolorkit MON-APP900BYGR (Blue, Yellow, Green, Red).
Principle of method:
Freezing medium
Reagents provided:
4x 100 ml Cryocompound, freezing medium (ready-to-use)
Storage and handling:
Store at room temperature
Procedure:
1. Place few drops of CryoCompound (depends on the size of the sample to be embedded) onto the center of the bottom of cryomold. Be careful to select the proper size embedding mold according to the size of the sample to be embedded. 2. Try to avoid the formation of air bubbles. Remove any bubbles inside the CryoCopound. This is important because the air bubbles will create problems when cutting sections. Air bubbles create freeze- thaw-freeze cycle and ice crystal will form inside of it and result in a very bad morphology due to the ice crystal artefact. 3. Let it settle for 15-30 seconds to allow the CryoCompound to completely wet the surface of the tissue. Hardening of the CryoCompound included the sample (it will happen in 0.5-1 minute) before preparing the CryoCompoundsample-block.
For in-vitro Diagnostic Use. The BrightVision Ultimate one step component detection system peroxidase Goat Anti-Mouse/Rabbit IgG HRP and DAB, is intended for use in immunohistochemistry for the detection of mouse or rabbit antibodies.
The BrightVision Ultimate detection system, peroxidase Goat Anti-Mouse/Rabbit HRP plus DAB, is a Ready-to-Use system that has been manufactured to give an optimal staining, when using the protocol advised in this IFU. Prior to staining some routine fixed, paraffin-embedding tissue sections should be subjected to pre-treatment (HIER or digestive enzyme). The BrightVision Ultimate detection system detects Mouse or Rabbit bound to an antigen in tissue sections. This polymer-complex is then visualized with a suitable substrate/chromogen. The clinical interpretation of any staining or its absence should be determined by a qualified pathologist and complemented by morphologic studies; controls should be evaluated within the context of the patients clinical history and/or other diagnostic tests.
Principle of method:
BrightVision Ultimate, one step detection system, Goat Anti-Mouse/Rabbit HRP (Ready-to-Use) plus DAB.
Reagents provided:
BrightVision Ultimate plus, one detection system, Goat Anti-Mouse/Rabbit HRP (Ready-to-Use) plus DAB 1. one step detection, Goat Anti-Mouse/Rabbit HRP (Ready-to-Use): 55 ml 2. DAB Solution A: Buffered H2O2 (Ready-to-Use): 83 ml 4. DAB Solution B: Concentrated DAB solution: 4 ml
Storage and handling:
2-8°C and in the dark
Reagent preparation:
Preparation DAB: Add 40?l DAB Solution B (one drop) to 1 ml substrate Solution A, mix well. Volume and the quality of the Bright DAB has been formulized so they also can be used in automatic stainers, when a higher volume is required.
Procedure:
1. Deparaffinize and rehydrate tissue section (slide/tissue peparing), 2. Wash Aqua dest (Wash; 2x 5 min), 3. If applicable, HIER or digestive enzyme (pre-treatment), 4. Wash buffer (PBS or TBS buffer; 2x 5 min), 5. H2O2 (conc3%) (Tissue preparing; 10 min), 6. Wash buffer (PBS or TBS buffer; 2x 5 min), 7. Primary mouse or rabbit antibody (Antibody; 30 min), 8. Wash buffer (PBS or TBS buffer; 2x 5 min), 9 Detection system, polymer Mouse/Rabbit HRP, (Labeled polymer; 30 min), 10. Wash buffer (PBS or TBS buffer; 2x 5 min), 11. Substrate (DAB; 8 min.; Preparation DAB: Add 40?l DAB Solution B (one drop) to 1 ml substrate Solution A, mix well. Volume and the quality of the Bright DAB has been formulized so they also can be used in automatic stainers, when a higher volume is required.), 14. Wash aqua dest (Wash; 2x 2 min), 15. Counterstain, dyhydrate and coverslip (Auxiliary.
Quality Control:
A positive control, negative control and reagent control are needed and processed in the same way as the unknow specimen slide to interpret staining results.
AEC Single Solution is a ready-to-use solution intended for immunohistochemical and in situ-hybridisation staining procedures with horse radish peroxidase (HRP). AEC (3-Amino-9-ethylcarbazol) leads to the formation of a red-brown precipitate at the location of the target antigen or target nucleic acid. The precipitate is insoluble in aqueous mounting media and can be observed by light microscopy. AEC Single Solution is especially useful when a high sensitivity is desired.
The solution should be stored at 2-8°C without furt her dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. AEC Single Solution is a ready-to-use solution. Preparation of a working solution as in other chromogenic substrates is not necessary. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents please contact our technical support.
Reagent preparation:
The solution is ready-to-use. AEC Single Solution can be used directly from the refrigerator and should be stored again at 2-8°C aft er use. When using the small package (8 ml MON-APP169) please directly drop from the bottle. When using the 100 ml package (MON_APP?) please transfer up to 8 ml of the AEC Single Solution into one of the provided dropper bottles. The transferred solution is stable for many weeks if stored at 2-8°C. The vo lume required for several staining runs should be transferred so that the 100 ml stock bottle has to be opened only a few times. If you would like to pipette the solution use a clean vial from which you pipette. Remaining quantities should not be filled back into the bottle but disposed as hazardous material.
Procedure:
1) Rinse the slide with wash buffer after the previous incubation step. 2) Apply the AEC Single Solution to the slide. Incubate for 3-6 minutes. (Incubation time can be extended up to 30 minutes, if desired.) 3) Rinse with distilled H2O. 4) Counterstain with haematoxylin for about 30 seconds up to 5 minutes (depending on the desired staining intensity). 5) Rinse with distilled H2O. 6) Blueing in tap water for at least 5 minutes. 7) Mount with an aqueous mounting medium.
Expected results:
During the reaction of the substrate with horse radish peroxidase in presence of the chromogen AEC, a red-brown precipitate is formed at the location of the target antigen or nucleic acid. The precipitate is insoluble in aqueous solvents and can be observed by light microscopy.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, or contact our technical support. Also refer to the instructions of the detection systems for guidance on general troubleshooting.
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). In some tissues endogenous peroxidase activity may cause non-specific staining. The enzyme activity should be blocked by incubation with hydrogen peroxide solution (H2O2 solution). The step is carried out before incubation with primary antibody but after dewaxing and rehydration. Background staining due to endogenous biotin can be blocked through an avidin-biotin blocking step prior to the primary antibody incubation step. The coloured precipitate formed by AEC is soluble in organic solvents. The tissue sections therefore have to be counterstained with aqueous solutions (e. g. Gills or Mayers haematoxylin) and mounted with aqueous mounting media. The colour intensity of the reaction product can decrease with time, especially when exposed to light. The staining reaction itself can be influenced in the same way when carried out in strong light. Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided
Precautions:
Use by qualified personnel only. AEC (3-Amino-9-ethylcarbazol) and the solvents used are considered hazardous materials. Material safety data sheets (MSDS) are available upon request. Wear protective clothing to avoid contact of reagent or specimen with eye, skin or mucous membrane. In case of reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Oxidising substances, e. g. metals, dust, bacteria or glass devices can influence the stability of AEC Single Solution. Such contaminations have to be avoided. Non-consumed solution needs to be discarded as dangerous substance.
The Plus HRP Polymer anti-Mouse kit is designed for the qualitative detection of antigens in fixed paraffinembedded tissue sections, in frozen tissue sections, and in cytological samples. It was developed for use in combination with monoclonal primary antibodies and sera obtained from mice. The reagent can be used for examining tissues fixed in different solutions, e.g. formalin (neutrally buffered), B5, Bouin, ethanol, or HOPE.
The purpose of the immunohistochemical staining is to make tissue and cell antigens visible. The Plus HRP Polymer anti-Mouse kit is a highly sensitive detection kit intended for use in immunohistochemistry and immunocytochemistry. The enzyme polymer consists of several molecules of secondary antibodies covalently bound to several molecules of horse radish peroxidase (HRP). Visualisation occurs via an enzyme-substrate reaction in the presence of a colorising reagent which permits microscopical analysis. The test system is suitable for the detection of monoclonal primary antibodies and sera obtained from mice. In contrast to other detection techniques, which often use the streptavidin-biotin system the Plus HRP Polymer antiMouse kit avoids the problem of background staining caused by endogenous biotin in the tissue
Principle of method:
Paraffin-embedded tissue sections are first deparaffinised and rehydrated. Endogenous peroxidase activity in the tissue may cause non-specific staining. This enzyme activity can be blocked by incubation with 3% H2O2-solution (peroxide block). Background staining caused by unspecific binding of the primary antibody or the secondary antibody in the HRPpolymer is minimized by incubation with a protein blocking solution. This step can be omitted if the primary antibodies are diluted in an appropriate buffer. The next step is incubation with the specific primary antibody. After washing, the HRP-polymer is applied and incubated. Any excess of unbound HRP-polymer is thoroughly washed away after incubation. The addition of the chromogenic substrate starts the enzymatic reaction of the peroxidase which leads to colour precipitation where the primary antibody is bound. The colour can be observed with a light microscope. The chromogen used determines the colour. The chromogen AEC leads to the formation of a red-brown product of reaction at the place of the target antigen. The chromogen DAB forms a dark brown precipitate.
Reagents provided:
100 mL HRP-Polymer anti-Mouse (ready-to-use) Substrate systems recommended: Permanent AEC kit, AEC single solution, AEC substrate kit, DAB substrate kit, DAB High contrast kit. Materials required but not supplied: Positive und negative control tissue Xylene or suitable substitutes Ethanol, distilled H2O 3% H2O2 solution Reagents for enzyme digestion or heat pre-treatment Wash buffer PBS or TBS PAP Pen Primary antibody (user-defined) Primary antibody diluent Negative control reagent Chromogenic substrate Counter stain solution Mounting medium Cover slips
Storage and handling:
The solution should be stored at 2-8°C without further dilution. Please store the reagent in a dark place and do not freeze it. Under these conditions the solution is stable up to the expiry date. It should not be used after the expiry date. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by the kit reagents, please contact our technical support .
Reagent preparation:
Reagent should be at room temperature when used. Deparaffinise and rehydrate paraffin-embedded tissue sections. Pre-treatment (optional) with HIER (Heat Induced Epitope Retrieval) or enzymatic digestion. Tissue sections have to be completely covered with the different reagents in order to avoid drying out.
Procedure:
1. Peroxide blocking (3 % H2O2 solution) 10 min. 2. Washing with wash buffer 1 x 2 min. 3. Blocking Solution (This step is optional.) 5 min. 4. Washing with wash buffer 1 x 2 min. 5. Primary antibody (optimally diluted) or negative control reagent 30-60 min. 6. Washing with wash buffer 3 x 5 min. 7. HRP-polymer anti-Mouse 30 min. 8. Washing with wash buffer 3 x 2 min. 9. AEC or DAB (Controlling the colour intensity via light microscope is recommended.) 5-15 min. 10. Stopping the reaction with distilled H2O when the desired colour intensity is attained 11. Counterstaining and blueing 12. Mounting: aqueous with AEC, permanent with DAB or Permanent AEC
Expected results:
During the reaction of the substrate with horse radish peroxidase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results which could possibly be caused by the reagents, please read these instructions carefully, contact our technical support . No staining on an actually positive control slide: 1. Reagents were not used in the proper order. 2. Chromogenic substrate solution was too old. 3. Bleaching because chromogen and mounting medium are incompatible. 4. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. Try a pre-treatment such as heat pre-treatment or enzyme digestion. If you used a pre-treatment it should be extended. 5. Primary antibody not from mouse but from a different species. 6. The antigen/epitope was not stable in the fixation and/or pre-treatment procedure used. Try another fixation or pre-treatment. Weak staining: 1. Inadequate fixation or overfixation. 2. Incomplete deparaffinisation. 3. The antigen/epitope in the tissue was insufficiently accessible to the primary antibody. If you used heat pre-treatment or enzyme digestion it should be extended. 4. Excessive incubation with Blocking Solution or insufficient washing after this step. 5. Too much wash buffer remains on the slides after washing, diluting the reagents applied in the next step. 6. Incubation times were too short or primary antibody concentration too low. 7. Chromogenic substrate solution was too old. Nonspecific background staining or overstaining: 1. Incomplete deparaffinisation. 2. Excessive tissue adhesive on slides. 3. Insufficient washing especially after the incubation with the enzyme polymer or the chromogenic substrate solution. These washings are critical. 4. Tissue was allowed to (partially) dry out with reagents on. 5. Unspecific binding of the primary antibody. Please use the Blocking Solution provided with this kit or dilute the primary antibody in appropriate diluents. 6. Incubation time of the primary antibody was too long or primary antibody concentration too high. 7. Incubation time of the chromogenic substrate solution was too long or reaction temperature too high (e.g. if temperature in the laboratory is high). 8. The substrate is metabolised by endogenous horse radish peroxidase in the tissue. Maybe the hydrogen peroxide solution used for blocking was inactivated
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex method in which histological as well as immunological detection methods are combined. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Endogenous peroxidase or pseudoperoxidase activity may cause non-specific staining. The enzyme activity is blocked by incubation with hydrogen peroxide solution. Tissues containing Hepatitis B Surface Antigen (HBsAg) may give false positive results with HRP (horse radish peroxidase) detection systems (Omata et al, 1980). Inadequate counterstaining and mounting can influence the interpretation of the results. The colour intensity of the reaction product can decrease with time, especially when exposed to light. Overexposure with the protein blocking solution can result in decreasing signal intensity. Sanbio guarantee that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid eye, skin or mucous membrane contact with the reagents. In case of the reagent coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining might appear. ProClin 950 is used for stabilisation. A Material safety data sheets (MSDS) is available upon request.
Antibody Diluent B is especially developed for dilution of certain primary antibodies. Antibodies diluted with Antibody Diluent B are primarily used in immunohistochemistry with formalin-fixed paraffin-embedded tissue sections, but also with frozen, HOPE-fixed, and cytological samples as well as in immunoblot procedures.
Antibody diluents used in immunohistochemistry should protect the antibody from microbial contamination and stabilize the antibody chemically. Antibody Diluent B reduces non-specific binding of antibodies to tissue sections and is therefore extremely useful in receiving background-free staining results.
Principle of method:
Immunohistochemical staining procedures often start with incubation of a blocking solution to reduce unspecific binding of primary antibody to tissue sections. This step can be omitted if the antibody used is diluted in Antibody Diluent B. Antibody Diluent B minimises unspecific binding of the primary antibody to the tissue section, reduces surface tension of the antibody solution and improves spreading the reagent on the slide, increases microbial and chemical stability of the antibody, reduces adhesion of antibody to the surface of the vial, and minimises the danger of antibody degradation by proteolytic enzymes.
Reagents provided:
100 ml Antibody Diluent B (ready-to-use)
Storage and handling:
The solution should be stored at 2-8°C without furt her dilution. Do not freeze it. Under these conditions the solution is stable up to the expiry date indicated on the label. Do not use product after the expiry date. If stored at room temperature the solution is stable for at least 10 month from the date of delivery. A positive and a negative control have to be carried out in parallel to the test material. If you observe unusual staining or other deviations from the expected results which could possibly be caused by this reagent, please contact our technical support.
Expected results:
During the reaction of the substrate with horse radish peroxidase or alkaline phosphatase in the presence of a chromogen, a coloured precipitate is formed at the location of the bound primary antibody. This reaction only takes place if the target antigen is existent in the tissue. The chromogen used determines the colour of the precipitate. The analysis is carried out using a light microscope.
Trouble shooting:
If you observe unusual staining or other deviations from the expected results please read these instructions carefully, contact our technical support. Also refer to the instructions of the detection systems containing Peroxide Block for guidance on general troubleshooting
Quality Control:
We recommend carrying out a positive and a negative control with every staining run. The positive control permits the validation of appropriate processing of the sample. If the negative control has a positive result, this points to unspecific staining. Please refer to the instructions of the detection system for guidance on general quality control procedures.
Performance characteristics:
Studies have been conducted to evaluate the performance of the kit reagents. The product has been found to be suitable for the intended use
Limitations of procedure:
Immunohistochemistry is a complex technique involving both histological and immunological detection methods. It requires a highly trained histotechnologist. Tissue processing and handling prior to immunostaining, for example variations in fixation and embedding or the inherent nature of the tissue can cause inconsistent results (Nadji and Morales, 1983). Inadequate counterstaining and mounting can influence the interpretation of the results.Sanbio guarantees that the product will meet all requirements described from its shipping date until its expiry date, as long as the product is correctly stored and utilized. No additional guarantees can be given. Under no circumstances shall Sanbio be liable for any damages arising out of the use of the reagent provided.
Precautions:
Use by qualified personnel only. Wear protective clothing to avoid contact of reagent or specimen with eye, skin or mucous membrane. In case of the reagent or specimen coming into contact with a sensitive area, wash the area with large amounts of water. Microbial contamination of the reagent must be avoided, since otherwise non-specific staining may occur. (NaN3), used for stabilisation, is not considered hazardous material in the concentration used. Sodium azide deposits in drainage pipes made of lead or copper can result in the formation of highly explosive metallic azides. To avoid such deposits in drainage pipes, sodium azide should be discarded in a large volume of running water. A material safety data sheet (MSDS) is available upon request.
Store lyophilized/reconstituted at -20 °C; once reconstituted make aliquots to avoid repeated freeze-thaw cycles. Please remember to spin the tubes briefly prior to opening them to avoid any losses that might occur from material adhering to the cap or sides of the tube.
Host Animal:
Rabbit
Species Reactivity:
Arabidopsis thaliana, Hordeum vulgare, Picea abies, Picea glauca, Pinus strobus, Spinacia oleracea, Drosera capensis. These antibodies have been shown to be reactive in all dicots, monocots, and gymnosperms
Immunogen:
BSA or KLH-conjugated synthetic peptides derived from conserved regions of plant Lhca1-4 and Lhcb1-6 protein sequences.
For detection of algal LHC proteins, we recommend: Set of 4 Chlamydomonas anti-Lhc antibodies
Application Details:
This set contains the following antibodies:Product number:Product name: AS01 005AS01 006AS01 007AS01 008AS01 004AS01 003AS01 002AS04 045AS01 009AS01 010Anti-Lhca1Anti-Lhca2Anti-Lhca3Anti-Lhca4Anti-LhcbAnti-Lhcb2Anti-Lhcb3Anti-Lhcb4Anti-Lhcb5Anti-Lhcb6Product AS01 009 and AS01 010 can be sold containing ProClin if requested.
Purity:
Total IgG. Protein G purified in PBS pH 7.4.: AS01 005, AS01 006, AS01 007, AS01 008, AS01 002, AS04 045 affinity purified serum: AS01 004, AS01 003. Serum: AS01 009, AS01 010.
Reconstitution:
For reconstitution add sterile water according to label on each tube
Molecular Weight:
20 - 29 kDa
Not reactive in:
No confirmed exceptions from predicted reactivity are currently known
Selected references:
Merry et al. (2017). A comparison of pine and spruce in recovery from winter stress; changes in recovery kinetics, and the abundance and phosphorylation status of photosynthetic proteins during winter. Tree Physiol. 2017 Sep 1;37(9):1239-1250. doi: 10.1093/treephys/tpx065.Li et al. (2017). NYEs/SGRs-mediated chlorophyll degradation is critical for detoxification during seed maturation in Arabidopsis. Plant J. 2017 Nov;92(4):650-661. doi: 10.1111/tpj.13710. Epub 2017 Oct 20.Yoshida et al. (2016). Hisabori T1.Two distinct redox cascades cooperatively regulate chloroplast functions and sustain plant viability. Proc Natl Acad Sci U S A. 2016 Jul 5;113(27):E3967-76. doi: 10.1073/pnas.1604101113. Epub 2016 Jun 22.Pavlovič et al. (2016). A carnivorous sundew plant prefers protein over chitin as a source of nitrogen from its traps. Plant Physiol Biochem. 2016 Mar 5;104:11-16. doi: 10.1016/j.plaphy.2016.03.008Xu et al. (2011). Light-harvesting chlorophyll a/b-binding proteins are required for stomatal response to abscisic acid in Arabidopsis. J. Ex. Bot. Dec 5 (ahead of print).Kang et al. (2010). Evaluation of light-harvesting complex proteins as senescence-related protein markers in detached rice leaves. Photosynthetica 47, 4:638-640.
PEB is an extraction buffer for disruption and solubilisation of total protein from plant tissue and algal cells. The use of the anionic detergent LDS together with the recommended procedure (combination of sonication and freeze/thaw cycles) has been shown to increase the number of solubilised and non-degraded proteins when compared to other methods of cell disruption (see reference). The estimated hands-on time for the recommended procedure is 20-30 minutes for 1-2 samples. Expected yields will be 1.5-6 g/ l total protein (recovered from standard procedure) depending on the starting material, e.g. its biological stage, homogenization method used (bead beater vs. sonication).
Product Type:
Antibody
Storage Temp:
Stable at RT for at least 1 month; short-term storage (6 monthss) at 4°Cand long term storage (1 year or more) at -20 °C.
Species Reactivity:
PEB has been tested on a wide range of species and tissues from Higher plants, Mosses, Llichens, Algae, Diatoms, Dinoflagellates, Cyanobacteria. Extracts may be quantified using detergent (LDS) compatible methods, and have been shown to give highly reproducible and quantitative results in subsequent SDS PAGE gel electrophoresis, Western blotting, and Immunoprecipitation (IP). Most of Agrisera commercial antibodies are tested on plant or algal samples extracted with this buffer. An example can be found here.
5 x 2 ml (4x stock) allows up to 75 isolations of plant material (using 500 µl 1x PEB for 100 mg fresh weight) or 190 isolations of algal material (using 200 µl 1x PEB for cell amounts corresponding to 4-10 µg total chlorophyll)
Selected references:
Altuntas et al. (2020). Proline-stimulated signaling primarily targets the chlorophyll degradation pathway and photosynthesis associated processes to cope with short-term water deficit in maize. Photosynth Res. 2020 Apr;144(1):35-48. doi: 10.1007/s11120-020-00727-w.P rez-L pez et al. (2020). Transcriptome Analysis Identifies Plasmodiophora brassicae Secondary Infection Effector Candidates. J Eukaryot Microbiol. 2020 Jan 11. doi: 10.1111/jeu.12784.Morin et al. (2019). Morin et al. (2019). Response of the sea-ice diatom Fragilariopsis cylindrus to simulated polar night darkness and return to light. Limnology and Oceanography. 9999, 2019, 1â??20. (sea-ice diatom)Bausch, A.R., Juhl, A.R., Donaher, N.A. et al. Mar Biol (2019) 166: 80.Matsuo and Atsumi (2018). Xylosylation of proteins by expression of human xylosyltransferase 2 in plants. J Biosci Bioeng. 2018 Sep;126(3):371-378. doi: 10.1016/j.jbiosc.2018.03.013.Brouwer et al. (2011) TheImpact ofLightIntensity onShade-InducedLeaf Senescence. Plant Cell Environ. Dec. 15 (ahead of print).Kosawang et al. (2011) Hydrogen yield from a hydrogenase in Frankia R43 at different levels of the carbon source propionate. Journal of Environmental Management, Jan 26
Special application note:
Buffer components (4x): contains ~ 40% v/v glycerol [HOCH2CH(OH)CH2OH], Tris-HCl [NH2C(CH2OH)3 HCl] pH 8.5, LDS [CH3(CH2)11OSO3Li], EDTA [(HO2CCH2)2NCH2CH2N(CH2CO2H)2]It is recommended to include a protease inhibitor (not supplied with this buffer) from a freshly made stock while preparing the ready-to-use 1x PSB.PEB has been optimized for quantitative small-scale preparation of whole protein extracts from plant/algal tissue. Extraction using the procedure described below will result in maximum yield of proteins and diminish protein degradation and aggregation.Extracts may be quantified using detergent (LDS) compatible methods and have been shown to give highly reproducible and quantitative results in subsequent SDS PAGE gel electrophoresis, Western Blotting, and immunoprecipitation.PEB has been tested on a wide range of species and tissues from higher plants, mosses, lichens, algae, diatoms, dinoflagellates, and cyanobacteria.
Store lyophilized/reconstituted at -20 °C; once reconstituted make aliquots to avoid repeated freeze-thaw cycles. Please remember to spin the tubes briefly prior to opening them to avoid any losses that might occur from material adhering to the cap or sides of the tube.
Host Animal:
Rabbit, Secondary antibody: Goat,
Species Reactivity:
Algae, Cyanobacteria, Higher plants
Immunogen:
KLH-conjugated syntetic peptides for respective antibodies, see product info sheets
50 µl of respective antibody, 100 µl of each protein standard, 2 x 10 µl of secondary antibody, 10 ml of ECL reagent,
Estimation of PSI to PSII ratio can be done using quantitative western blot technique using anti-PsaC (PSI) and PsbA (PSII) antibodies. References: Brown et al. (2007). Resource dynamics during infection of Micromonas pusilla by virus MpV-SP1. Environmental Microbiology 9(11): 2720-2727. Brown et al. (2008). Flux capacities and acclimation costs in Trichodesmium from the Gulf of Mexico. Marine Biology 154 (3): 413-422.
Selected references:
Abramson (2018). CARBON PARTITIONING IN ENGINEERED CYANOBACTERI UM FOR THE STUDY OF FEEDBACK INHIBITION OF PHOTOSYNTHESIS. Michigan State University, ProQuest Dissertations Publishing, 2018. 10826228.Morash et al. (2007) Macromolecular dynamics of the photosynthetic system over a seasonal developmental progression in Spartina alterniflora. Can J. of Bot. 85: 476-483(8)Bouchard et al. (2006) UVB effects on the photosystem II-D1 protein of phytoplankton and natural phytoplankton communities. Photochem and Photobiol 82: 936-951.MacKenzie et al (2005). Large reallocations of carbon, nitrogen and photosynthetic reductant among phycobilisomes, photosystems and Rubisco during light acclimation in Synechococcus elongatus are constrained in cells under low environmental inorganic carbon. Arch of Microbiol. 183: 190 - 202.
Special application note:
Product information - Primary antibodies:Product number:Product name:Reconstitution: Recommended dilution:AS03 037Rabbit Anti-RbcL Global antibodyFor reconstitution see lable on respective tube.1:5000-10 000 with ECLAS10 939Rabbit Anti-PsaC Global antibodyFor reconstitution see lable on respective tube.1:1000 with ECLAS05 084Rabbit Anti-PsbAGlobal antibodyFor reconstitution see lable on respective tube.1:10 000 with ECL* All primary antibodies in this kit are raised in rabbits.Product information - Protein standards:Product number:Product name:Concentration:Size:Western Blot – Positive Control:AS01 016SPsbA *0.25 pmol/ μl41.5 kDa#To generate a standard curve, 3 loads are suggested (0.5, 2 and 4 ul). For most applications a sample load of 0.2 ug of chlorophyll will give a PsbA signal in this range.A 2 ul load is optimal for most chemiluminescent detection systems to use as a positive control.AS01 017SRbcL *0.15 pmol/ μl52.7 kDaTo generate a standard curve, 3 loads are suggested (0.5, 2 and 4 ul). For most applications a sample load of 0.2 ug of chlorophyll will give a RbcL signal in this range.A 2 ul load is optimal for most chemiluminescent detection systems to use as a positive control.AS04 042SPsaC *0.15 pmol/μl11.5 kDa#To generate a standard curve, 3 loads are suggested (0.5, 2 and 4 l). For most applications a sample load of 0.2 g of chlorophyll will give a PsaC signal in this range.A 2 ul load is optimal for most chemiluminescent detection systems as a positive control.*These proteins are larger than a respective native protein due to the addition of His-tag* For reconstitution of standards see lable on respective tube.Product information - Secondary antibody:AS09 602-trial Goat anti-Rabbit IgG (H&L), HRP conjugated, 20 l (2x10 l)Product information - ECLreagent:AS16 ECL-N-10 AgriseraECL Bright (10 ml trial pack)Educational information about Quantitative western blot can be found here: detailed method description, video tutorial
The outer light-harvesting antenna of the photosystems (PSI and PSII) of the green unicellular alga Chlamydomonas reinhardtii is composed of pigment-binding proteins belonging to the Lhc family highly conserved in photosynthetic eukaryotes. Some of the Lhc-subtypes of Chlamydomonas share sufficient high similarity with the respective functional homologs in plants to allow specific detection with antisera generated against conserved peptide domains from plant Lhc-proteins.
Product Type:
Antibody
Antibody Type:
Polyclonal
Format:
Lyophilized
Storage Temp:
Store lyophilized/reconstituted at -20 °C; once reconstituted make aliquots to avoid repeated freeze-thaw cycles. Please remember to spin the tubes briefly prior to opening them to avoid any losses that might occur from material adhering to the cap or sides of the tube.
Lhcb4 - higher plants (use AS04 045 for those organsims), algae, cyanobacteria
Selected references:
Lhcb2 Du et al. (2018). Galactoglycerolipid Lipase PGD1 Is Involved in Thylakoid Membrane Remodeling in Response to Adverse Environmental Conditions in Chlamydomonas. Plant Cell. 2018 Feb;30(2):447-465. doi: 10.1105/tpc.17.00446. Lhcb4Jeong et al. (2017). Deletion of the chloroplast LTD protein impedes LHCI import and PSI-LHCI assembly in Chlamydomonas reinhardtii. J Exp Bot. 2017 Dec 30. doi: 10.1093/jxb/erx457. Lhcb5 and Lhcbm5 Takahashi et al. (2006). Identification of the mobile light-harvesting complex II polypeptides for state transitions in Chlamydomonas reinhardtii. PNAS 103:477-482
RbcL antibody and protein standard: Please store at -20 °C (6 months) or -80°Cfor long term storage(years). Please avoid freezing and thawing of reconstituted antibodies, make aliquots instead. PEB extraction buffer:Stable at RT for at least 1 month. For short-term storage please stoore (1 month) at 4°Cand for long term storage (1 year) at -20 °C.
Alpha proteobacteria, Algae (brown and red), Beta-proteobacteria, Dicots, Conifers, Cryptomonad, Cyanobacteria, Gamma-proeobacteria, Liverworts, Mosses, Prochlorophytes, PelwitschiaSpecies of your interest not listed? Contact us
Immunogen:
KLH-conjugated synthetic peptide was used to elicit anti-RbcL antibody. No baculovirus was used in production of this product.
1 x 50 µl of AS03 037, RbcL | Rubisco large subunit, form I and form II (amount enough for 50-100 Western blots)1 x 100 µl of AS01 017S, Rubisco protein standard (0.15 pmoles / µl, amount enough for generation of standard curve in 34 assays (standard curve: 0.0625 pmoles, 0.125 pmoles, 0.25 pmoles)2 x 2 ml of AS08 300, Protein extraction buffer (amount enough for 48 isolations of plant material, using 500 µl 1x PEB for 100 mg fresh weight) or 120 isolations of algal material (using 200 µl 1x PEB for cell amounts corresponding to 4-10 µg total chlorophyll)2 x 10 µl of AS09 602, Goat anti-rabbit IgG (H&L), HRP conjugated(amount enough for 50-100 Western blots)1 X 10 ml of AS16 ECL-N-10, AgriseraECL Bright 10 ml (5 ml of component A + 5 ml of component B, trial pack)
Quantitative western blot: detailed method description, video tutorialDiscussion over some critical aspects of quantitative western blot: Heidebrecht et al. (2009). Improved semiquantitative Western blot technique with increased quantification range. J. Immunological Methods. 35:40-48.
Defez et al. (2019). Bacterial IAA-Delivery into Medicago Root Nodules Triggers a Balanced Stimulation of C and N Metabolism Leading to a Biomass Increase. Microorganisms. 2019 Sep 29;7(10). pii: E403. doi: 10.3390/microorganisms7100403.Sorrentino et al. (2018). Performance of three cardoon cultivars in an industrial heavy metal-contaminated soil: Effects on morphology, cytology and photosynthesis. J Hazard Mater. 2018 Jun 5;351:131-137. doi: 10.1016/j.jhazmat.2018.02.044.Mota et al. (2015). Effects of heavy metals on Cyanothece sp. CCY 0110 growth, extracellular polymeric substances (EPS) production, ultrastructure and protein profiles. J Proteomics. 2015 Apr 29;120:75-94. doi: 10.1016/j.jprot.2015.03.004.Thamatrakoln et al. (2013). Death-specific protein in a marine diatom regulates photosynthetic responses to iron and light availability. Proc Natl Acad Sci U S A. 2013 Dec 10;110(50):20123-8. doi: 10.1073/pnas.1304727110. Supplemental material describes western blot quantification method.
2 x 50 ml, two component ready to use solutions, enough for 50 midi blots (6,8 x 8,1 cm), which is 2754 cm2
Selected references:
Wieczorek et al. (2020) Development of a New Tomato Torrado Virus-Based Vector Tagged with GFP for Monitoring Virus Movement in Plants. Viruses. 2020 Oct 20;12(10):1195. doi: 10.3390/v12101195. PMID: 33092281; PMCID: PMC7588970.Fallah et al. (2018). Plasminogen activation is required for the development of radiation-induced dermatitis. Cell Death Dis. 2018 Oct 15;9(11):1051. doi: 10.1038/s41419-018-1106-8.
2 x 50 ml, two component ready to use solutions, enough for 50-60 midi blots (6,8 x 8,1 cm)
Special application note:
Highly stable for 18 month at 2 C to 8 C. Working stock is stable for 7 days at room temperature and 30 days at +4 C. Lot to lot consistency.High sensitivity, low background and superior signal to noice ratios.
ExoTEST Ready to Use Kit is the ideal platform for capturing and the quantifying exosomes from biological samples such as plasma and urine. ExoTEST Ready to Use Kit features pre-coated ELISA plate with primary antibodies detection directed against exosome-specific markers, namely ?-CD9. Secondary antibodies and substrate reagents are included in the kit. Exosome standards for assay calibration are also included in the kit. Exosome standards are purified by ultracentrifugation and microfiltration, quantified for overall protein content and exosome number and then lyophilized for long-term storage. ExoTEST ready to use kits are reliable, easy to use, works on a variety of commercially available detection technologies.
Background Info:
Sample type: Plasma
Starting material: Up to 100 ul of biological sample can be loaded per well. Unfractionated plasma sample can be directly used for capture. Concentrated urine samples are recommended prior capture according to our suggested protocol.
Assay type: Sandwich enzyme-linked immunoassay.
Sensitivity: The detection limit of an assay is lower than 0.35 ug of overall exosome which is an equivalent of less than 50 pg of targeted exosomes protein.
Product overview: ExoTEST Ready to Use Kit is the ideal platform for capturing and the quantifying exosomes from biological samples such as plasma and urine.
ExoTEST Ready to Use Kit features pre-coated ELISA plate with primary antibodies detection directed against exosome-specific markers, namely ?-CD9. Secondary antibodies and substrate reagents are included in the kit.
Exosome standards for assay calibration are also included in the kit. Exosome standards are purified by ultracentrifugation and microfiltration, quantified for overall protein content and exosome number and then lyophilized for long-term storage.
ExoTEST ready to use kits are reliable, easy to use, works on a variety of commercially available detection technologies.
Primary antibody: ?-CD9 mouse antibody
Exosome standard: Lyophilized exosomes from plasma of healthy donors (see details).
Assay protocol: Kit contains all the reagents necessary for exosome capture and protein targeted detection.
Assay calibration: Kit contains exosome standards for assay calibration. Depended on the sample type used, kit may include human plasma, serum or urine exosomes. All exosome standards are lyophilized and quantified for overall protein content and exosomes number.
This standards enable both absolute and relative quantification exosomes in analyzed samples.
Product Type:
immunoplate
Storage Temp:
+ 4 C
Applications:
Exosome capture and quantification
Additional Info:
Kit contains all the reagents necessary for exosome capture and protein targeted detection. Assay calibration: Kit contains exosome standards for assay calibration. Depended on the sample type used, kit may include human plasma, serum or urine exosomes. All exosome standards are lyophilized and quantified for overall protein content and exosomes number. This standards enable both absolute and relative quantification exosomes in analyzed samples.
Application Details:
Exosome capture and quantification using the ExoTEST ensures dose-dependent exosome detection in a variety of samples. The quantification can be both relative and absolute as the assay calibration enables the calculation of the approximate exosome quantity for each sample.
Comprehensive exosome profiling by implementing different combinations of capture and detection antibodies. ExoTEST can be customized for assessing multiple antigens in a total exosome population within a sample. Informative protein profiles for the samples of interest can be combined with subsequent nucleic acid (mRNA or miRNA) extraction and downstream analysis from captured exosomes.
Specific diagnostic applications using the ExoTEST allows the quantitative assessment of total circulating exosomes and specific exosomal sub-populations, defined by differentially expressed antigens under normal and pathological conditions.
HBM provides a ready to use kit for the qualitative FACS analysis of exosomes. The Exo-FACS assay for exosome characterisation consists of 4um beads used for the direct overall capture of pre-purified, validated and lyophilized exosomes from cell culture supernatants or human biological fluids. The characterization of exosomal proteins (membrane expressed or internal) is subsequently performed using appropriate detection antibodies against exosome associated antigens.
Background Info:
Exosomes are small endosome derived lipid nanoparticles (50-120 nm) actively secreted by exocytosis by most living cells. Exosome release occurs either constitutively or upon induction, under both normal and pathological conditions, in a dynamic, regulated and functionally relevant manner. Both amount and molecular composition of released exosomes depend on the state of a parent cell. Exosomes have been isolated from diverse cell lines (hematopoietic cells, tumor lines, primary cultures, virus infected cells) as well as from biological fluids in particular blood (e.g. serum and plasma from cancer patients) and other body fluids (bronchoalveolar lavage fluid, pleural effusions, synovial fluid, urine, amniotic fluid, semen, saliva etc). Exosomes have pleiotropic physiological and pathological functions and an emerging role in diverse pathological conditions such as cancer, infectious and neurodegenerative diseases.
Product Type:
FACS analysis
Storage Temp:
+ 4 C
Applications:
FACS Exosome isolation and exosome marker characterization via FACS. Exosome comprehensive profiling.
No initial exosome purification required User friendly and reliable and efficient Suitable for multiple marker analyses Available in custom format
Starting material: Up to 100 ul of biological sample can be loaded per well. Unfractionated serum sample can be directly used for capture.
Assay type: Sandwich enzyme-linked immunoassay.
Sensitivity: The detection limit of an assay is lower than 0.35 ug of overall exosome which is an equivalent of less than 50 pg of targeted exosomes protein.
Product overview: ExoTEST Ready to Use Kit is the ideal platform for capturing and the quantifying exosomes from biological samples such as plasma and urine.
ExoTEST Ready to Use Kit features pre-coated ELISA plate with primary antibodies detection directed against exosome-specific markers, namely ?-CD9. Secondary antibodies and substrate reagents are included in the kit.
Exosome standards for assay calibration are also included in the kit. Exosome standards are purified by ultracentrifugation and microfiltration, quantified for overall protein content and exosome number and then lyophilized for long-term storage.
ExoTEST ready to use kits are reliable, easy to use, works on a variety of commercially available detection technologies.
Primary antibody: ?-CD9 mouse antibody
Exosome standard: Lyophilized exosomes from serum of healthy donors (see details).
Assay protocol: Kit contains all the reagents necessary for exosome capture and protein targeted detection.
Assay calibration: Kit contains exosome standards for assay calibration. All exosome standards are lyophilized and quantified for overall protein content and exosomes number.
This standards enable both absolute and relative quantification exosomes in analyzed samples. HansaBioMed also provides a range of exosome standards purified from different types of human cells that can be purchased separately or included in custommade kits in order to meet the need for detection of specific exosome markers.
Product Type:
immunoplate
Storage Temp:
+ 4 C
Applications:
Exosome capture and quantification
Additional Info:
Kit contains all the reagents necessary for exosome capture and protein targeted detection. Assay calibration: Kit contains exosome standards for assay calibration. Depended on the sample type used, kit may include human plasma, serum or urine exosomes. All exosome standards are lyophilized and quantified for overall protein content and exosomes number. This standards enable both absolute and relative quantification exosomes in analyzed samples.
Application Details:
Exosome capture and quantification using the ExoTEST ensures dose-dependent exosome detection in a variety of samples. The quantification can be both relative and absolute as the assay calibration enables the calculation of the approximate exosome quantity for each sample.
Comprehensive exosome profiling by implementing different combinations of capture and detection antibodies. ExoTEST can be customized for assessing multiple antigens in a total exosome population within a sample. Informative protein profiles for the samples of interest can be combined with subsequent nucleic acid (mRNA or miRNA) extraction and downstream analysis from captured exosomes.
Specific diagnostic applications using the ExoTEST allows the quantitative assessment of total circulating exosomes and specific exosomal sub-populations, defined by differentially expressed antigens under normal and pathological conditions.
HBM provides a ready to use kit for the qualitative FACS analysis of exosomes. The Exo-FACS assay for exosome characterisation consists of 4um beads used for the direct overall capture of pre-purified, validated and lyophilized exosomes from cell culture supernatants or human biological fluids. The characterization of exosomal proteins (membrane expressed or internal) is subsequently performed using appropriate detection antibodies against exosome associated antigens.
Background Info:
Exosomes are small endosome derived lipid nanoparticles (50-120 nm) actively secreted by exocytosis by most living cells. Exosome release occurs either constitutively or upon induction, under both normal and pathological conditions, in a dynamic, regulated and functionally relevant manner. Both amount and molecular composition of released exosomes depend on the state of a parent cell. Exosomes have been isolated from diverse cell lines (hematopoietic cells, tumor lines, primary cultures, virus infected cells) as well as from biological fluids in particular blood (e.g. serum and plasma from cancer patients) and other body fluids (bronchoalveolar lavage fluid, pleural effusions, synovial fluid, urine, amniotic fluid, semen, saliva etc). Exosomes have pleiotropic physiological and pathological functions and an emerging role in diverse pathological conditions such as cancer, infectious and neurodegenerative diseases.
Product Type:
FACS analysis
Storage Temp:
+ 4 C
Applications:
FACS Exosome isolation and exosome marker characterization via FACS. Exosome comprehensive profiling.
ExoTEST has been developed to fill the need for a reliable method to quantify exosomes and examine their biomarkers. >>>> HansaBioMed also provide the ability to design and create your own kit by choosing from among the wide variety of reagents available in our catalog. 1-Select the exosome standard you need. 2-Select the primary antibody for exosome detection.
HBM provides a ready to use kit for the qualitative FACS analysis of exosomes. The Exo-FACS assay for exosome characterisation consists of 4um beads used for the direct overall capture of pre-purified, validated and lyophilized exosomes from cell culture supernatants or human biological fluids. The characterization of exosomal proteins (membrane expressed or internal) is subsequently performed using appropriate detection antibodies against exosome associated antigens.
Background Info:
Exosomes are small endosome derived lipid nanoparticles (50-120 nm) actively secreted by exocytosis by most living cells. Exosome release occurs either constitutively or upon induction, under both normal and pathological conditions, in a dynamic, regulated and functionally relevant manner. Both amount and molecular composition of released exosomes depend on the state of a parent cell. Exosomes have been isolated from diverse cell lines (hematopoietic cells, tumor lines, primary cultures, virus infected cells) as well as from biological fluids in particular blood (e.g. serum and plasma from cancer patients) and other body fluids (bronchoalveolar lavage fluid, pleural effusions, synovial fluid, urine, amniotic fluid, semen, saliva etc). Exosomes have pleiotropic physiological and pathological functions and an emerging role in diverse pathological conditions such as cancer, infectious and neurodegenerative diseases.
Product Type:
FACS analysis
Storage Temp:
+ 4 C
Applications:
FACS Exosome isolation and exosome marker characterization via FACS. Exosome comprehensive profiling.
No initial exosome purification required User friendly and reliable and efficient Suitable for multiple marker analyses Available in custom format
The ExoTEST Ready to Use Kit is the ideal platform for capturing and quantifying exosomes from biological samples. It features ELISA plate(s) pre-coated with primary antibodies to exosome-specific markers, plus the secondary antibody, substrate reagents and the exosome standards. Plus we can also help you customise your own kit by choosing from the individual reagents available in our catalog.
Background Info:
Exosomes are small endosome derived lipid nanoparticles (50-120 nm) actively secreted by exocytosis by most living cells. Exosome release occurs either constitutively or upon induction, under both normal and pathological conditions, in a dynamic, regulated and functionally relevant manner. Both amount and molecular composition of released exosomes depend on the state of a parent cell. Exosomes have been isolated from diverse cell lines (hematopoietic cells, tumor lines, primary cultures, virus infected cells) as well as from biological fluids in particular blood (e.g. serum and plasma from cancer patients) and other body fluids (bronchoalveolar lavage fluid, pleural effusions, synovial fluid, urine, amniotic fluid, semen, saliva etc). Exosomes have pleiotropic physiological and pathological functions and an emerging role in diverse pathological conditions such as cancer, infectious and neurodegenerative diseases.
Product Type:
FACS analysis
Storage Temp:
+ 4 C
Applications:
FACS Exosome isolation and exosome marker characterization via FACS. Exosome comprehensive profiling.
ExoTEST has been developed to fill the need for a reliable method to quantify exosomes and examine their biomarkers. >>>> HansaBioMed also provide the ability to design and create your own kit by choosing from among the wide variety of reagents available in our catalog. 1-Select the exosome standard you need. 2-Select the primary antibody for exosome detection.
Starting material: Up to 100 ul of biological sample can be loaded per well. Unfractionated plasma sample can be directly used for capture. Concentrated urine samples are recommended prior capture according to our suggested protocol.
Assay type: Sandwich enzyme-linked immunoassay.
Sensitivity: The detection limit of an assay is lower than 0.35 ug of overall exosome which is an equivalent of less than 50 pg of targeted exosomes protein.
Product overview: ExoTEST Ready to Use Kit is the ideal platform for capturing and the quantifying exosomes from biological samples such as plasma, serum, urine and cell culture supernatant. ExoTEST Ready to Use Kit features pre-coated ELISA plate with primary antibodies detection directed against exosome-specific markers, namely ?-CD9. Secondary antibodies and substrate reagents are included in the kit. Exosome standards for assay calibration are also included in the kit. Exosome standards are purified by ultracentrifugation and microfiltration, quantified for overall protein content and exosome number and then lyophilized for long-term storage. ExoTEST ready to use kits are reliable, easy to use, works on a variety of commercially available detection technologies.
Primary antibody: ?-CD9 murine antibody.
Exosome standard: Lyophilized exosomes from COLO-1 Cell culture supernatant (see details).
Assay protocol: Kit contains all the reagents necessary for exosome capture and protein targeted detection.
Assay calibration: kit contains exosome standards for assay calibration. All exosome standards are lyophilized and quantified for overall protein content and exosomes number.
This standards enable both absolute and relative quantification exosomes in analyzed samples.
Product Type:
immunoplate
Storage Temp:
+ 4 C
Applications:
Exosome capture and quantification
Additional Info:
Kit contains all the reagents necessary for exosome capture and protein targeted detection. Assay calibration: Kit contains exosome standards for assay calibration. Depended on the sample type used, kit may include human plasma, serum or urine exosomes. All exosome standards are lyophilized and quantified for overall protein content and exosomes number. This standards enable both absolute and relative quantification exosomes in analyzed samples.
Application Details:
Exosome capture and quantification using the ExoTEST ensures dose-dependent exosome detection in a variety of samples. The quantification can be both relative and absolute as the assay calibration enables the calculation of the approximate exosome quantity for each sample.
Comprehensive exosome profiling by implementing different combinations of capture and detection antibodies. ExoTEST can be customized for assessing multiple antigens in a total exosome population within a sample. Informative protein profiles for the samples of interest can be combined with subsequent nucleic acid (mRNA or miRNA) extraction and downstream analysis from captured exosomes.
Specific diagnostic applications using the ExoTEST allows the quantitative assessment of total circulating exosomes and specific exosomal sub-populations, defined by differentially expressed antigens under normal and pathological conditions.
Exosomes are small endosome derived lipid nanoparticles (50-120 nm) actively secreted by exocytosis by most living cells. Exosome release occurs either constitutively or upon induction, under both normal and pathological conditions, in a dynamic, regulated and functionally relevant manner. Both amount and molecular composition of released exosomes depend on the state of a parent cell. Exosomes have been isolated from diverse cell lines (hematopoietic cells, tumor lines, primary cultures, virus infected cells) as well as from biological fluids in particular blood (e.g. serum and plasma from cancer patients) and other body fluids (bronchoalveolar lavage fluid, pleural effusions, synovial fluid, urine, amniotic fluid, semen, saliva etc). Exosomes have pleiotropic physiological and pathological functions and an emerging role in diverse pathological conditions such as cancer, infectious and neurodegenerative diseases.
Product Type:
Enolase kit
Storage Temp:
+ 4 C
Additional Info:
No initial exosome purification required User friendly and reliable and efficient Suitable for multiple marker analyses Available in custom format
ExoTEST Ready to Use Kit is the ideal platform for capturing and the quantifying exosomes from biological samples such as plasma and urine. ExoTEST Ready to Use Kit features pre-coated ELISA plate with primary antibodies detection directed against exosome-specific markers, namely ?-CD9. Secondary antibodies and substrate reagents are included in the kit. Exosome standards for assay calibration are also included in the kit. Exosome standards are purified by ultracentrifugation and microfiltration, quantified for overall protein content and exosome number and then lyophilized for long-term storage. ExoTEST ready to use kits are reliable, easy to use, works on a variety of commercially available detection technologies.
Background Info:
Sample type: Urine
Starting material: Up to 100 ul of biological sample can be loaded per well. Unfractionated plasma sample can be directly used for capture. Concentrated urine samples are recommended prior capture according to our suggested protocol.
Assay type: Sandwich enzyme-linked immunoassay.
Sensitivity: The detection limit of an assay is lower than 0.35 ug of overall exosome which is an equivalent of less than 50 pg of targeted exosomes protein.
Product overview: ExoTEST Ready to Use Kit is the ideal platform for capturing and the quantifying exosomes from biological samples such as plasma and urine.
ExoTEST Ready to Use Kit features pre-coated ELISA plate with primary antibodies detection directed against exosome-specific markers, namely ?-CD9. Secondary antibodies and substrate reagents are included in the kit.
Exosome standards for assay calibration are also included in the kit. Exosome standards are purified by ultracentrifugation and microfiltration, quantified for overall protein content and exosome number and then lyophilized for long-term storage.
ExoTEST ready to use kits are reliable, easy to use, works on a variety of commercially available detection technologies.
Primary antibody: ?-CD9 mouse antibody
Exosome standard: Lyophilized exosomes from urine of healthy donors (see details).
Assay protocol: Kit contains all the reagents necessary for exosome capture and protein targeted detection.
Assay calibration: Kit contains exosome standards for assay calibration. Depended on the sample type used, kit may include human plasma, serum or urine exosomes. All exosome standards are lyophilized and quantified for overall protein content and exosomes number.
This standards enable both absolute and relative quantification exosomes in analyzed samples.
Product Type:
immunoplate
Storage Temp:
+ 4 C
Applications:
Exosome capture and quantification
Additional Info:
Kit contains all the reagents necessary for exosome capture and protein targeted detection. Assay calibration: Kit contains exosome standards for assay calibration. Depended on the sample type used, kit may include human plasma, serum or urine exosomes. All exosome standards are lyophilized and quantified for overall protein content and exosomes number. This standards enable both absolute and relative quantification exosomes in analyzed samples.
Application Details:
Exosome capture and quantification using the ExoTEST ensures dose-dependent exosome detection in a variety of samples. The quantification can be both relative and absolute as the assay calibration enables the calculation of the approximate exosome quantity for each sample.
Comprehensive exosome profiling by implementing different combinations of capture and detection antibodies. ExoTEST can be customized for assessing multiple antigens in a total exosome population within a sample. Informative protein profiles for the samples of interest can be combined with subsequent nucleic acid (mRNA or miRNA) extraction and downstream analysis from captured exosomes.
Specific diagnostic applications using the ExoTEST allows the quantitative assessment of total circulating exosomes and specific exosomal sub-populations, defined by differentially expressed antigens under normal and pathological conditions.
Up to 100 ul of biological sample can be loaded per well.
Concentrated cell culture supernatant samples are recommended prior capture according to our suggested protocol.
Assay type:
Sandwich enzyme-linked immunoassay.
Sensitivity:
The detection limit of an assay is lower than 0.35 ug of overall exosome which is an equivalent of less than 50 pg of targeted exosomes protein.
Product overview: ExoTEST Ready to Use Kit is the ideal platform for capturing and the quantifying exosomes from cell culture supernatant. ExoTEST Ready to Use Kit features pre-coated ELISA plate with primary antibodies detection directed against exosome-specific markers, namely ?-CD9. Secondary antibodies and substrate reagents are included in the kit. Exosome standards for assay calibration are also included in the kit. Exosome standards are purified by ultracentrifugation and microfiltration, quantified for overall protein content and exosome number and then lyophilized for long-term storage.
ExoTEST ready to use kits are reliable, easy to use, works on a variety of commercially available detection technologies.
Primary antibody: ?-CD9 mouse antibody.
Exosome standard: Lyophilized exosomes from COLO-1 Cell culture supernatant (see details).
Assay protocol: Kit contains all the reagents necessary for exosome capture and protein targeted detection.
Assay calibration: Kit contains exosome standards prepared from purified from proprietary human cell line for assay calibration. All exosome standards are lyophilized and quantified for overall protein content and exosomes number.
HansaBioMed also provides a range of exosome standards purified from different types of human cells that can be purchased separately or included in custom kits in order to meet the need for detection of specific exosome markers.
Background Info:
Sample type: Cell culture supernatant.
Starting material: Up to 100 ul of biological sample can be loaded per well. Concentrated cell culture supernatant samples are recommended prior capture according to our suggested protocol.
Assay type: Sandwich enzyme-linked immunoassay.
Sensitivity: The detection limit of an assay is lower than 0.35 ug of overall exosome which is an equivalent of less than 50 pg of targeted exosomes protein.
Product overview: ExoTEST Ready to Use Kit is the ideal platform for capturing and the quantifying exosomes from cell culture supernatant. ExoTEST Ready to Use Kit features pre-coated ELISA plate with primary antibodies detection directed against exosome-specific markers, namely ?-CD9. Secondary antibodies and substrate reagents are included in the kit. Exosome standards for assay calibration are also included in the kit. Exosome standards are purified by ultracentrifugation and microfiltration, quantified for overall protein content and exosome number and then lyophilized for long-term storage.
ExoTEST ready to use kits are reliable, easy to use, works on a variety of commercially available detection technologies.
Primary antibody: ?-CD9 mouse antibody.
Exosome standard: Lyophilized exosomes from COLO-1 Cell culture supernatant (see details).
Assay protocol: Kit contains all the reagents necessary for exosome capture and protein targeted detection.
Assay calibration: Kit contains exosome standards prepared from purified from proprietary human cell line for assay calibration. All exosome standards are lyophilized and quantified for overall protein content and exosomes number.
HansaBioMed also provides a range of exosome standards purified from different types of human cells that can be purchased separately or included in custom kits in order to meet the need for detection of specific exosome markers.
Product Type:
immunoplate
Storage Temp:
+ 4 C
Applications:
Exosome capture and quantification
Additional Info:
Kit contains all the reagents necessary for exosome capture and protein targeted detection. Assay calibration: Kit contains exosome standards prepared from purified from proprietary human cell line for assay calibration. All exosome standards are lyophilized and quantified for overall protein content and exosomes number. HansaBioMed also provides a range of exosome standards purified from different types of human cells that can be purchased separately or included in custom kits in order to meet the need for detection of specific exosome markers.
Application Details:
Exosome capture and quantification using the ExoTEST ensures dose-dependent exosome detection in a variety of samples. The quantification can be both relative and absolute as the assay calibration enables the calculation of the approximate exosome quantity for each sample.
Comprehensive exosome profiling by implementing different combinations of capture and detection antibodies. ExoTEST can be customized for assessing multiple antigens in a total exosome population within a sample. Informative protein profiles for the samples of interest can be combined with subsequent nucleic acid (mRNA or miRNA) extraction and downstream analysis from captured exosomes.
Specific diagnostic applications using the ExoTEST allows the quantitative assessment of total circulating exosomes and specific exosomal sub-populations, defined by differentially expressed antigens under normal and pathological conditions.
Expression system for standard: E.coli; Immunogen sequence: S24-S91
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Mouse Rantes with <1pg/ml sensitivity Compatible samples: cell culture supernatants. serum and plasma (heparin, EDTA, citrate). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
mouse
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Expression system for standard: NS0; Immunogen sequence: A27-R190
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Mouse VEGF with <2pg/ml sensitivity Compatible samples: cell culture supernatants, serum and plasma (heparin, EDTA, citrate). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
mouse
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Nephrin ELISA Kit (96 Tests). Quantitate Human NPHS1 in cell culture supernatants, serum and plasma (heparin, EDTA or citrate). Sensitivity: 50pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: Q23-S1055
Applications:
ELISA
Additional Info:
For quantitative detection of human Nephrin in cell culture supernatants, serum and plasma (heparin, EDTA, citrate).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat SEMA3F ELISA Kit (96 Tests). Quantitate Rat SEMA3F in cell culture supernatants, serum and plasma (heparin, EDTA or citrate). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: A19-T785
Applications:
ELISA
Additional Info:
For quantitative detection of rat SEMA3F in cell culture supernatants, serum and plasma (heparin, EDTA, citrate).
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat BDNF Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Rat Bdnf in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA, citrate). Sensitivity: 15pg/ml.
Product Type:
Assay & Detection
Storage Temp:
-20°C
Immunogen:
Expression system for standard: NS0; Immunogen sequence: H129-R247
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Rat BDNF whit <15pg/ml sensitivity Compatible samples: cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA, citrate). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat EGF Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Rat Egf in cell culture supernatants, serum, plasma (heparin, EDTA) and urine. Sensitivity: 1pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: E.coli; Immunogen sequence: N974-R1026
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Rat EGF with <1pg/ml sensitivity Compatible samples: cell culture supernatants, serum, plasma (heparin, EDTA) and urine. This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Myostatin/GDF8 ELISA Kit (96 Tests). Quantitate Human MSTN in cell culture supernatants, tissue, serum and plasma (heparin or EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: D267-S375
Applications:
ELISA
Additional Info:
For quantitative detection of human Myostatin/GDF8 in cell culture supernatants, tissue, serum and plasma(heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human LAP (TGF-Beta1) ELISA Kit (96 Tests). Quantitate Human LAP(TGF-Beta1) in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: L30-R278
Applications:
ELISA
Additional Info:
For quantitative detection of human LAP(TGF-beta1) in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human TIMP3 Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human TIMP3 in cell culture supernatants, serum, plasma (heparin , EDTA) and saliva. Sensitivity: 2pg/ml.
Product Type:
Assay & Detection
Storage Temp:
-20°C
Immunogen:
Expression system for standard: NS0; Immunogen sequence: C24-P211
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human TIMP3 with <2pg/ml sensitivity Compatible samples: cell culture supernatants, serum, plasma(heparin , EDTA) and saliva. This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Granzyme A ELISA Kit (96 Tests). Quantitate Human GZMA in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: I29-V262
Applications:
ELISA
Additional Info:
For quantitative detection of human Granzyme A in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Expression system for standard: NS0; Immunogen sequence: W42-A709
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Mouse P-Selectin/CD62P with <5pg/ml sensitivity Compatible samples: cell culture supernatants, serum and plasma (citrate). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
mouse
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human G-CSF Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human CSF3 in cell culture supernatants, serum and plasma (heparin, EDTA, citrate). Sensitivity: 4pg/ml.
Product Type:
Assay & Detection
Storage Temp:
-20°C
Immunogen:
Expression system for standard: E.coli; Immunogen sequence: T31-P204
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human G-CSF with <4pg/ml sensitivity Compatible samples: cell culture supernatants, serum and plasma (heparin, EDTA, citrate). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Cystatin C/CST3 Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human CST3 in cell culture supernatants, serum, plasma (heparin, EDTA) , saliva, urine and human milk. Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
-20°C
Immunogen:
Expression system for standard: NS0; Immunogen sequence: M1-A146
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human CST3 with <10pg/ml sensitivity Compatible samples: cell culture supernatants, serum, plasma(heparin, EDTA), saliva, urine and human milk. This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat Serpin D1 ELISA Kit (96 Tests). Quantitate Rat Serpind1 in cell culture supernatants, serum and plasma (EDTA, citrate) and urine. Sensitivity: 0.1ng/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: E24-S479
Applications:
ELISA
Additional Info:
For quantitative detection of rat Serpin D1 in cell culture supernatants, serum and plasma (EDTA, citrate) and urine.
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat KIM1 Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Rat Havcr1 in cell culture supernatants, serum, plasma (heparin, EDTA) and urine. Sensitivity: 2pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: S18-V238
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Rat KIM1 with <2pg/ml sensitivity Compatible samples: cell culture supernatants, serum, plasma (heparin, EDTA) and urine. This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human GHR/Growth Hormone R ELISA Kit (96 Tests). Quantitate Human GHR in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 15pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: A27-Y264
Applications:
ELISA
Additional Info:
For quantitative detection of human GHR in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Kallistatin/Serpina4 Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human SERPINA4 in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: Q21-P427
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human Kallistatin/Serpina4 with <10pg/ml sensitivity Compatible samples: cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human IL-1RA/IL1RN Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human IL1RN in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 2pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: E.coli; Immunogen sequence: R26-E177
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human IL-1RA/IL1RN with <2pg/ml sensitivity Compatible samples: cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human IL-6 Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human IL6 in cell culture supernatants, serum and plasma (heparin, EDTA, citrate). Sensitivity: 0.3pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: E.coli; Immunogen sequence: P29-M212
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human IL-6 with <0.3pg/ml sensitivity Compatible samples: cell culture supernatants, serum and plasma (heparin, EDTA, citrate). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat Rantes Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Rat Ccl5 in cell culture supernatants. serum and plasma (heparin, EDTA, citrate). Sensitivity: 1pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: E.coli; Immunogen sequence: S24-S91
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Rat Rantes with <1pg/ml sensitivity Compatible samples: cell culture supernatants. serum and plasma (heparin, EDTA, citrate). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human HAI-2/SPINT2 Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human SPINT2 in cell culture supernatants, serum, plasma (heparin, EDTA) and cell lysates. Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: M1-K197
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human HAI-2/SPINT2 with <10pg/ml sensitivity Compatible samples: cell culture supernatants, serum, plasma (heparin, EDTA) and cell lysates. This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Granzyme B ELISA Kit (96 Tests). Quantitate Human GZMB in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: I21-Y247
Applications:
ELISA
Additional Info:
For quantitative detection of human Granzyme B in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human IL-4 Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human IL4 in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 1.5pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: E.coli; Immunogen sequence: H25-S153
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human IL-4 with <1.5pg/ml sensitivity Compatible samples: cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human TIMP-4 ELISA Kit (96 Tests). Quantitate Human TIMP4 in cell culture supernatants, serum, plasma (heparin, EDTA) and human milk. Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: C30-P224
Applications:
ELISA
Additional Info:
For quantitative detection of human TIMP-4 in cell culture supernatants, serum, plasma(heparin, EDTA) and human milk.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat CRP/C Reactive Protein ELISA Kit (96 Tests). Quantitate Rat Crp in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: H20-S230
Applications:
ELISA
Additional Info:
For quantitative detection of rat CRP in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human ICAM-1/CD54 Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human ICAM1 in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: Q28-E480
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human ICAM-1/CD54 with <10pg/ml sensitivity Compatible samples: cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Cystatin B ELISA Kit (96 Tests). Quantitate Human CSTB in cell culture supernatants, serum, plasma (heparin, EDTA) , saliva, urine and human milk. Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: E.coli; Immunogen sequence: M2-F98
Applications:
ELISA
Additional Info:
For quantitative detection of human Cystatin B in cell culture supernatants, serum, plasma(heparin, EDTA), saliva, urine and human milk.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat Lipocalin-2/NGAL Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Rat Lcn2 in cell culture supernatants, serum, plasma (heparin) and urine. Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: Q21-N198
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Rat Lipocalin-2/NGAL with <10pg/ml sensitivity Compatible samples: cell culture supernatants, serum, plasma (heparin) and urine. This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human TLR1 / TIL ELISA Kit (96 Tests). Quantitate Human TLR1 in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: S22-N578
Applications:
ELISA
Additional Info:
For quantitative detection of human TLR1 in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Laminin Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human Laminin in cell culture supernatants, cell lysates and serum. Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: from human fibroblasts
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human Laminin with <10pg/ml sensitivity Compatible samples: cell culture supernatants, cell lysates and serum. This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat BMP-9 ELISA Kit (96 Tests). Quantitate Rat Gdf2 in bone tissue, cell culture supernatants, serum and plasma (heparin, EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: CHO; Immunogen sequence: S320-R430
Applications:
ELISA
Additional Info:
For Quantitative Detection of rat BMP-9 in bone tissue, cell culture supernatants, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human MBL2/MPB-C Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human MBL2 in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: E21-I248
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human MBL2/MPB-C with <10pg/ml sensitivity Compatible samples: cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human NOTCH1 / TAN 1 ELISA Kit (96 Tests). Quantitate Human NOTCH1 in cell culture supernatants, serum and plasma (heparin, EDTA). Sensitivity: 12pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: A19-Q526
Applications:
ELISA
Additional Info:
For Quantitative Detection of human NOTCH1 in cell culture supernatants, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human IGF2R/IGF-II R ELISA Kit (96 Tests). Quantitate Human IGF2R in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: S1510-F2108
Applications:
ELISA
Additional Info:
For quantitative detection of human IGF2R in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat Myostatin/GDF8 ELISA Kit (96 Tests). Quantitate Rat MSTN in cell culture supernatants, tissue, serum and plasma (heparin or EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: D268-S376
Applications:
ELISA
Additional Info:
For quantitative detection of rat Myostatin/GDF8 in cell culture supernatants, tissue, serum and plasma(heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat Angiopoietin-2 Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Rat Angpt2 in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 15pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: Y19-F496
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Rat Angiopoietin-2 with <15pg/ml sensitivity Compatible samples: cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat Adiponectin Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Rat Adipoq in cell culture supernatants, serum, plasma (heparin, EDTA) and urine. Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: E.coli; Immunogen sequence: I19-N244
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Rat Adiponectin with <10pg/ml sensitivity Compatible samples: cell culture supernatants, serum, plasma (heparin, EDTA) and urine. This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat Activin A ELISA Kit (96 Tests). Quantitate Rat Inhba in cell culture supernatants, serum, plasma (heparin, EDTA) and saliva. Sensitivity: 12pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: CHO; Immunogen sequence: G311-S426
Applications:
ELISA
Additional Info:
For quantitative detection of rat Activin A in cell culture supernatants, serum, plasma(heparin, EDTA) and saliva.
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat MMP-2 Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Rat Mmp2 in cell culture supernatants, serum and plasma (heparin). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: A30-C662
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Rat MMP-2 with <10pg/ml sensitivity Compatible samples: cell culture supernatants, serum and plasma (heparin). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Expression system for standard: E.coli; Immunogen sequence: L80-L235
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Mouse Tnf with <1pg/ml sensitivity Compatible samples: cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
mouse
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human FLRG/FSTL3 ELISA Kit (96 Tests). Quantitate Human FSTL3 in cell culture supernatants, serum, plasma (heparin, EDTA) , urine and human milk. Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: M27-V263
Applications:
ELISA
Additional Info:
For quantitative detection of human FLRG in cell culture supernatants, serum, plasma(heparin, EDTA), urine and human milk.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Ficolin-1/FCN1/M Ficolin Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human FCN1 in cell culture supernatants, serum and plasma (heparin). Sensitivity: 20pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: A30-A326
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human Ficolin-1/FCN1/M Ficolin with <20pg/ml sensitivity Compatible samples: cell culture supernatants, serum and plasma (heparin). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Ficolin-1 / FCN1 / M Ficolin ELISA Kit (96 Tests). Quantitate Human FCN1 in cell culture supernatants, serum and plasma (heparin). Sensitivity: 20pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: A30-A326
Applications:
ELISA
Additional Info:
For quantitative detection of human Ficolin-1 in cell culture supernatants, serum and plasma(heparin).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Fetuin B ELISA Kit (96 Tests). Quantitate Human FETUB in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 12pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: C16-P382
Applications:
ELISA
Additional Info:
For quantitative detection of human Fetuin B in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Rat BMP-7 ELISA Kit (96 Tests). Quantitate Rat Bmp7 in bone tissue, cell culture supernatants, serum and plasma (heparin, EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: CHO; Immunogen sequence: S292-H430
Applications:
ELISA
Additional Info:
For quantitative detection of rat BMP-7 in bone tissue, cell culture supernatants, serum and plasma((heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
rat
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Cathepsin D ELISA Kit (96 Tests). Quantitate Human CTSD in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 10 pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: L21-L412
Applications:
ELISA
Additional Info:
For quantitative detection of human Cathepsin D in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human CXCL10/IP-10 Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human CXCL10 in cell culture supernatants, serum, plasma (heparin, EDTA), saliva and urine. Sensitivity: 1pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: E.coli; Immunogen sequence: V22-P98
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human CXCL10/IP-10 with <1pg/ml sensitivity Compatible samples: cell culture supernatants, serum, plasma (heparin, EDTA), saliva and urine. This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Endostatin ELISA Kit (96 Tests). Quantitate Human COL18A1 in cell culture supernatants, serum, plasma (heparin, EDTA) and human milk. Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: E.coli; Immunogen sequence: H1154-S1335
Applications:
ELISA
Additional Info:
For quantitative detection of human Endostatin in cell culture supernatants, serum, plasma(heparin, EDTA) and human milk.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human soluble EGFR ELISA Kit (96 Tests). Quantitate Human EGFR in cell culture supernatants, serum, plasma (heparin, EDTA) and human milk. Sensitivity: 1pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: M1-S645
Applications:
ELISA
Additional Info:
For quantitative detection of human EGFR in cell culture supernatants, serum, plasma(heparin, EDTA) and human milk.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human SP-D / Surfactant protein D ELISA Kit (96 Tests). Quantitate Human SFTPD in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 20pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: A21-F375
Applications:
ELISA
Additional Info:
For quantitative detection of human SP-D in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human sL-Selectin Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human SELL in cell culture supernatants, serum and plasma (heparin, EDTA, citrate). Sensitivity: 5pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: W39-N332
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human sL-Selectin with <5pg/ml sensitivity Compatible samples: cell culture supernatants, serum and plasma (heparin, EDTA, citrate). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human CCL22/MDC Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human CCL22 in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 1pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: E.coli; Immunogen sequence: G25-Q93
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Human CCL22/MDC with <1pg/ml sensitivity Compatible samples: cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human DLL1 ELISA Kit (96 Tests). Quantitate Human DLL1 in cell culture supernatants, serum, plasma (heparin, EDTA) , urine and human milk. Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: S22-G540
Applications:
ELISA
Additional Info:
For quantitative detection of human DLL1 in cell culture supernatants, serum, plasma(heparin, EDTA), urine and human milk.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human CD105 Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human ENG in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 15pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: CHO; Immunogen sequence: E26-G586
Applications:
ELISA
Additional Info:
The Quick version of ELISA kits, assay takes less than 1.5 hours. Detect Human Endoglin/ENG with <15pg/ml sensitivity
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Serpin D1 ELISA Kit (96 Tests). Quantitate Human SERPIND1 in cell culture supernatants, serum and plasma (EDTA, citrate) and urine. Sensitivity: 0.1ng/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: G20-S499
Applications:
ELISA
Additional Info:
For quantitative detection of human Serpin D1 in cell culture supernatants, serum and plasma (EDTA, citrate) and urine.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Cathepsin E ELISA Kit (96 Tests). Quantitate Human CTSE in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: Q18-P396
Applications:
ELISA
Additional Info:
For quantitative detection of human Cathepsin E in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human C-MET/HGFR ELISA Kit (96 Tests). Quantitate Human MET in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 5pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: E25-R307 (alpha) & S308-T932 (beta)
Applications:
ELISA
Additional Info:
For quantitative detection of human C-MET in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human Cathepsin B ELISA Kit (96 Tests). Quantitate Human CTSB in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA). Sensitivity: 5pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: R18-I339
Applications:
ELISA
Additional Info:
For quantitative detection of human Cathepsin B in cell culture supernatants, cell lysates, serum and plasma (heparin, EDTA).
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Expression system for standard: E.coli; Immunogen sequence: F25-T211
Applications:
ELISA
Additional Info:
The Quick ELISA kits, assay takes less than 1.5 hours. Detect Mouse IL-6 with <1pg/ml sensitivity Compatible samples: cell culture supernatants, serum and plasma (heparin, EDTA, citrate). This is a TMB colorimetric sandwich ELISA kit with short assay time and quick experiment set up.
Biosite Brand:
BioSite ELISA
Species Reactivity:
mouse
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human sTNFsR II ELISA Kit (96 Tests). Quantitate Human TNFRSF1B in cell culture supernatants, serum, plasma ( heparin, EDTA, citrate) and urine. Sensitivity: 2pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: L23-D257
Applications:
ELISA
Additional Info:
For quantitative detection of human soluble TNFsRII in cell culture supernatants, serum, plasma( heparin, EDTA, citrate) and urine.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
Human TGF Alpha ELISA Kit (96 Tests). Quantitate Human TGFA in cell culture supernatants, serum, plasma (heparin, EDTA) and human milk. Sensitivity: 1pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: E.coli; Immunogen sequence: V40-A89
Applications:
ELISA
Additional Info:
For quantitative detection of human TGF alpha in cell culture supernatants, serum, plasma(heparin, EDTA) and human milk.
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is cross-reactivity with TGF beta 2, TGF beta 3, TGF beta 5<1%.
Human B7-1/CD80 Quick ELISA Kit (90 minutes, 96 Tests). Quantitate Human CD80 in cell culture supernatants and serum. Sensitivity: 10pg/ml.
Product Type:
Assay & Detection
Storage Temp:
Mixed
Immunogen:
Expression system for standard: NS0; Immunogen sequence: V35-N242
Applications:
ELISA
Additional Info:
The Quick version of ELISA kits, assay takes less than 1.5 hours. Detect Human B7-1/CD80 with <10pg/ml sensitivity
Biosite Brand:
BioSite ELISA
Species Reactivity:
human
Cross Reactivity:
There is no detectable cross-reactivity with other relevant proteins.
EntrezGene ID:
941
UniProt No:
P33681
Cookies:
X
We use cookies to help personalise and improve your web experience.
By using our website you consent to our use of cookies, some of which may have already been set on your device.
View our Cookie Policy to learn more.
